GraphTec Cutting Plotter Discussion

General discussion pertaining to the GraphTec cutting plotters. (Please do not post support requests here)

496 topics in this forum

  1. Craft Robo Info

    By BannerJohn,
    • 5 replies
    • 12,756 views

  2. info from graphtec for cutmaster 3 and Graphtec studio

    By Dakotagrafx,
    • 4 replies
    • 6,103 views

  3. Graphtec FC 8600 - 75 not scanning to third pinch roller

    By Robtherod,
    • 1 reply
    • 222 views

  4. Graphect CE6000-60 PLUS which cable needed?

    By StotheP,
    • 1 reply
    • 273 views

  5. iMark software is not calibrating

    By JACS,
    • 3 replies
    • 600 views

  6. Graphtec CE6000-60 stops cutting in the middle of a job

    By Panthercountry,
    • 1 reply
    • 280 views

  7. Graphtec F-Mark 1 suckers: looking for the old style

    By Spam on Maui,
    • 10 replies
    • 3,342 views

  8. CrossCut Not Cutting Entire Width

    By westman,   
    • 2 replies
    • 2,985 views

  9. Removing parts of a design to make a stencil

    By Worble7,
    • 9 replies
    • 3,382 views

  10. Aligning multiple pen colours

    By Phillup,
    • 4 replies
    • 2,137 views

  11. Graphtec CE LITE-50 Cutting Strip question

    By BedlamBarber,
    • 17 replies
    • 2,467 views

  12. FC7000-75

    By elvis@signtekfl.com,
    • 1 reply
    • 1,034 views

  13. FCX2000 very slow than FC8600 for same speed

    By diltech,
    • 5 replies
    • 1,624 views

  14. FC9000 cutting slightly off on some files only

    By Anetski,
    • 0 replies
    • 1,622 views

  15. Graphtec FC7000 MK2-130 Help - Stuttering/Struggling

    By Archonx93,
    • 6 replies
    • 1,994 views

  16. FC8000 won't receive cut data

    By Solidroque,
    • 3 replies
    • 1,698 views

  17. Graphtec CE-7000 with a combo Machine labeler

    By James159,
    • 0 replies
    • 1,264 views

  18. ce7000-60 8.5 x 11 max. working area

    By Daryl,
    • 5 replies
    • 3,655 views

  19. Cutting Master 5 not cutting outer edges

    By UO-Jeremy,   
    • 10 replies
    • 5,217 views

  20. Graphtec FC9000 Take Up System

    By JustCut,
    • 0 replies
    • 1,055 views

  21. Can we contour cut outside of registration marks?

    By kcherdch,
    • 1 reply
    • 2,165 views

  22. Cutting Master 5 Contour cutting is not supported for multi-page design

    By UO-Jeremy,   
    • 11 replies
    • 8,524 views

  23. FC8600-Cut Master 4 issue

    By jeffdpia,   
    • 3 replies
    • 2,104 views

  24. Graphtec 6000-40 Plus: stopped die cutting, blades dulling fast

    By Spam on Maui,
    • 8 replies
    • 2,739 views

  25. Graphtec FC8600 cant hold calibration

    By Bigfoot Graphix,
    • 4 replies
    • 3,300 views