USCutter Refine Cutting Plotter Discussion

811 topics in this forum

1. questions before buying

   By RPM Graphics, September 30, 2009
   • 1 reply
   • 664 views
   • 
   • Rodger
   • September 30, 2009

2. Need to buy 48"...any suggestions?

   By splash0321, September 30, 2009
   • 0 replies
   • 608 views
   • 
   • splash0321
   • September 30, 2009

3. Another Newbie

   By ramy, September 24, 2009
   • 15 replies
   • 1,324 views
   • 
   • Guest sciondrgn
   • September 28, 2009

4. I'm an idiot

   By suzy, September 3, 2009
   • 8 replies
   • 1,469 views
   • 
   • prestonservco
   • September 27, 2009

5. speed rate

   By mailman, September 26, 2009
   • 2 replies
   • 751 views
   • 
   • mailman
   • September 26, 2009

6. Cuts not completing....

   By kenimes, March 10, 2008
   • 3 replies
   • 1,119 views
   • 
   • Brandon_Davis
   • September 25, 2009

7. Just a thought

   By Team Satan, September 24, 2009
   • 0 replies
   • 662 views
   • 
   • Team Satan
   • September 24, 2009

8. Refine (Bridge Pro720) Parallel cable pinout

   By Sinbadusa, September 20, 2009
   • 10 replies
   • 2,127 views
   • 
   • Guest crshirts
   • September 23, 2009

9. Refine Down!

   By tlzimmerman, September 17, 2009
   • 2 replies
   • 859 views
   • 
   • tlzimmerman
   • September 21, 2009

10. Suggested Force for MH 871

    By sspvinyl, September 14, 2009
    • 9 replies
    • 10,087 views
    • 
    • VendettaVinyl
    • September 20, 2009

11. Cutter is not cutting - Need help ASAP

    • 1
    • 2
    • 3

    By VendettaVinyl, September 11, 2009
    • 62 replies
    • 4,696 views
    • 
    • VendettaVinyl
    • September 19, 2009

12. mh365 driver help

    By bradshawwil, September 13, 2009
    • 1 reply
    • 2,458 views
    • 
    • MZ SKEETER
    • September 13, 2009

13. Can I cut around a injet t-shirt transfer with this?

    By cbauer50, September 12, 2009
    • 0 replies
    • 716 views
    • 
    • cbauer50
    • September 12, 2009

14. Help, cutter head slams into right side and making buzzing noise.

    By LukeBHC, September 11, 2009
    • 3 replies
    • 1,166 views
    • 
    • prestonservco
    • September 12, 2009

15. Refine with optical Eye

    By John Thomson, August 7, 2009
    • 18 replies
    • 4,584 views
    • 
    • CRD
    • September 9, 2009

16. Care to share your alignment procedure

    By Moto-X-Coatings, June 4, 2009
    • 9 replies
    • 1,478 views
    • 
    • pinhead_54
    • September 6, 2009

17. mh1351 - precision problems

    By b8studio, August 30, 2009
    • 3 replies
    • 1,648 views
    • 
    • cutme
    • September 1, 2009

18. MH721 hed wont lift on power up

    By signdork, July 8, 2009
    • 2 replies
    • 1,053 views
    • 
    • cpwall
    • August 31, 2009

19. Need help ASAP

    By midwestgamecompany, August 27, 2009
    • 5 replies
    • 930 views
    • 
    • jeremySI
    • August 30, 2009

20. mh721 is not cutting good circle

    By stickyicky612, October 27, 2008
    • 6 replies
    • 1,668 views
    • 
    • couturebling
    • August 21, 2009

21. sign blazer crashing

    By svplaser, August 19, 2009
    • 4 replies
    • 1,254 views
    • 
    • sarconastic
    • August 19, 2009

22. cut paths don't meet up

    By BigDaddyChris, August 6, 2009
    • 11 replies
    • 1,610 views
    • 
    • greens14
    • August 12, 2009

23. Jagged lines/letters with Refine 1351

    By Icedev, June 24, 2009
    • 17 replies
    • 1,911 views
    • 
    • Icedev
    • August 11, 2009

24. importing jpeg and bitmap graphics

    By hamnermitch, August 6, 2009
    • 1 reply
    • 634 views
    • 
    • cpwall
    • August 6, 2009

25. Drifting of vinyl?

    By RockerSigns, March 23, 2009
    • 6 replies
    • 1,425 views
    • 
    • tory
    • August 4, 2009