GraphTec Cutting Plotter Discussion

484 topics in this forum

1. Pricing Advice? Graphtec CE6000-40

   By clemail504, December 6, 2016
   • 3 replies
   • 971 views
   • 
   • slice&dice
   • December 6, 2016

2. Vinyl master pro version 4

   By Donnie, December 4, 2016
   • 0 replies
   • 819 views
   • 
   • Donnie
   • December 4, 2016

3. Graph tec ce6000-60

   By Donnie, December 2, 2016
   • 5 replies
   • 1,192 views
   • 
   • Donnie
   • December 3, 2016

4. clip art and tracing

   By bethann, December 1, 2016   

   • clip art
   • tracing
   • 8 replies
   • 2,057 views
   • 
   • PatrickR
   • December 6, 2016

5. CE6000-60 - printing/cutting on single sheets

   By calichick, October 30, 2016
   • 2 replies
   • 1,755 views
   • 
   • calichick
   • October 31, 2016

6. Incomplete/curved triangle test cut

   By ASmith137, October 17, 2016
   • 1 reply
   • 2,283 views
   • 
   • Dakotagrafx
   • October 17, 2016

7. Fc7000 main board

   By Carmigirl, October 15, 2016
   • 1 reply
   • 1,099 views
   • 
   • Carmigirl
   • October 15, 2016

8. Curves are Cutting Very Slowly

   By 13ruce, October 14, 2016   

   • speed
   • curves
   • (and 3 more)

     Tagged with:

     • speed
     • curves
     • slow
     • fc8600
     • technique
   • 3 replies
   • 2,063 views
   • 
   • 13ruce
   • November 1, 2016

9. Small cut at start of cutting

   By ofwgraphics, September 20, 2016
   • 1 reply
   • 1,170 views
   • 
   • Sal316
   • September 23, 2016

10. CE6000-60 pausing during cut

    By CJ Artisans, September 11, 2016
    • 3 replies
    • 2,111 views
    • 
    • Monkey
    • October 17, 2016

11. Graphtec Plotter Controller use

    By Carmigirl, September 6, 2016
    • 0 replies
    • 918 views
    • 
    • Carmigirl
    • September 6, 2016

12. GraphTec ce-6000-40 will not cut chrome?

    By DeonCarpenter, August 31, 2016
    • 4 replies
    • 1,294 views
    • 
    • FrznFire07
    • September 2, 2016

13. what am I doing wrong

    By bethann, August 31, 2016
    • 6 replies
    • 1,327 views
    • 
    • bethann
    • September 1, 2016

14. graphtec ce5000-60 Making Stencils

    By JeremyH, August 19, 2016
    • 3 replies
    • 2,773 views
    • 
    • PatrickR
    • August 20, 2016

15. Graphtec flash nv error

    By Leway, August 9, 2016
    • 5 replies
    • 1,939 views
    • 
    • mb20music
    • August 10, 2016

16. CE5000-60 Looking for part

    By Carlos Sanunga, June 17, 2016
    • 6 replies
    • 2,047 views
    • 
    • MZ SKEETER
    • June 17, 2016

17. Is the CE5000-60 actually compatible with Windows 10?

    By socceronly, May 27, 2016
    • 3 replies
    • 2,778 views
    • 
    • socceronly
    • May 27, 2016

18. IS THIS CAUSED FROM A DULL BLADE?

    By The Elvis Legacy, April 21, 2016
    • 8 replies
    • 2,051 views
    • 
    • mr300s
    • April 22, 2016

19. How to set Default Conditions?

    By ign 5, April 14, 2016   

    • fc7000-100 default changes
    • 3 replies
    • 1,623 views
    • 
    • ign 5
    • April 17, 2016

20. Cutting 22" wide on a 24" roll? (new Graphtec user)

    By Dorese, April 11, 2016   

    • Graphtec
    • Setup help
    • 4 replies
    • 1,139 views
    • 
    • MZ SKEETER
    • April 11, 2016

21. Graptec varying results

    By marduk, April 2, 2016
    • 24 replies
    • 2,402 views
    • 
    • bikemike
    • April 5, 2016

22. Graphtec FC5100 750

    By Signscreative, March 19, 2016
    • 1 reply
    • 866 views
    • 
    • mb20music
    • March 19, 2016

23. CE6000-60 Vacuum Hold Down?

    By Camel, March 10, 2016
    • 18 replies
    • 2,662 views
    • 
    • mfatty500
    • March 12, 2016

24. Help, FC7000 only cutting half page

    By ign 5, March 7, 2016
    • 12 replies
    • 3,420 views
    • 
    • MZ SKEETER
    • March 9, 2016

25. Graphtec Ce5000-60 Freezes

    By gcextreme, March 1, 2016
    • 20 replies
    • 3,770 views
    • 
    • darcshadow
    • May 17, 2016