GraphTec Cutting Plotter Discussion

General discussion pertaining to the GraphTec cutting plotters. (Please do not post support requests here)

484 topics in this forum

  1. ce6000-60

    By cardudenc,
    • 6 replies
    • 915 views

  2. CE6000-60 Newbie issues, Curves & Cut Controller

    By terranomade,
    • 35 replies
    • 15,128 views

  3. GT CE5000-60 MAC how to update firmware

    By RyanE,   
    • 1 reply
    • 1,684 views

  4. Die or Perf cutting with the CE5000

    By JK3,
    • 29 replies
    • 4,621 views

  5. Signblazer- CE6000

    By HOMESTEADSTENCIL,
    • 2 replies
    • 795 views

  6. Graphtec CE-6000 Using Knife instead of Pen to draw?

    By NickWhite,
    • 9 replies
    • 1,772 views

  7. Graphtec Question

    By bethfuciu,
    • 37 replies
    • 6,325 views

  8. Contour cutting error

    By Robert2495,   
    • 2 replies
    • 1,222 views

  9. SignBlazer and Graphtec CE-6000

    By SmallSigns,
    • 8 replies
    • 2,370 views

  10. contour cut?

    By ACJ GRAPHICS,
    • 3 replies
    • 923 views

  11. Blade carriage returns to left after cut

    By GwizGraphix,   
    • 5 replies
    • 1,597 views

  12. Graphtec CE6000-60

    By pmac,   
    • 4 replies
    • 1,628 views

  13. Incorrect cutting area on CE-6000-40 HELP!!!

    By dorlov,
    • 7 replies
    • 3,019 views

  14. HPGL driver for Graphtec FC2250

    By Patternmaker,   
    • 1 reply
    • 1,127 views

  15. Graphtec FC7000 Problems?

    By Phototec,   
    • 8 replies
    • 5,305 views

  16. FC 7000 Y position alarm. Did research just need some clarification.

    By BigHE,
    • 2 replies
    • 3,060 views

  17. GRAPHTEC USER AND SERVICE MANUALS PDF FOR MANY YEARS

    By MZ SKEETER,   
    • 7 replies
    • 3,941 views

  18. Can someone please help me figure out how to cut multiple designs on a cutting mat

    By southerlycharm,
    • 3 replies
    • 969 views

  19. CE-5000-60 issue

    By Poot25,
    • 5 replies
    • 1,258 views

  20. How to shut off Media sensor

    By GwizGraphix,
    • 3 replies
    • 2,688 views

  21. CE 6000-60 When cutting is changing the cutter setting on its own

    By KyleS,
    • 3 replies
    • 819 views

  22. Graphtec fc8600 cutting 3/16th inch off

    By dtdm,
    • 0 replies
    • 810 views

  23. New Graphtec CE6000-120 not detecting media width

    By larryinfl,
    • 5 replies
    • 2,654 views

  24. Print then cut fc7000

    By ign 5,   
    • 3 replies
    • 1,399 views

  25. Graphtec ce 5000-40 Not syncing with cutting master 3

    By yetna,
    • 32 replies
    • 27,538 views