LaserPoint Cutting Plotter Discussion

457 topics in this forum

1. LP 24 Contour Cutting Issues with SignCut Prod Pro. Help please! :D

   By NukleoN, June 21, 2010
   • 4 replies
   • 2,643 views
   • 
   • CRD
   • June 21, 2010

2. Blade Pressure, Speed, Offset, etc.

   By Larryc39, December 17, 2007
   • 7 replies
   • 2,636 views
   • 
   • skproductions08
   • January 4, 2008

3. Laserpoint and Signcut

   By Stlouistech, April 27, 2011
   • 3 replies
   • 2,602 views
   • 
   • TomasB
   • December 11, 2011

4. LaserPoint THREE (3) -- what's not to like?!!

   By slice&dice, April 9, 2018   

   • lp3
   • 11 replies
   • 2,581 views
   • 
   • MZ SKEETER
   • June 30, 2018

5. Contour cut offset issues

   By TomasB, March 20, 2011
   • 5 replies
   • 2,578 views
   • 
   • TomasB
   • December 11, 2011

6. Speed settings don't really work

   By MrJoel, August 5, 2017
   • 24 replies
   • 2,573 views
   • 
   • cardudenc
   • August 8, 2017

7. rattling chattering noise

   By cutme, March 18, 2008
   • 20 replies
   • 2,537 views
   • 
   • cutme
   • May 9, 2008

8. Blade holder and carriage arm questions

   By barrypatch, October 30, 2011
   • 6 replies
   • 2,482 views
   • 
   • barrypatch
   • November 19, 2011

9. Can the laserpoint cut 30 mil magnets?

   By topcatfavors, April 23, 2008
   • 16 replies
   • 2,480 views
   • 
   • haumana
   • June 19, 2008

10. USCutter LaserPoint Vinyl Cutter 48'' vs. Graphtec

    By cucuruchito, June 16, 2010
    • 2 replies
    • 2,467 views
    • 
    • Dakotagrafx
    • June 17, 2010

11. Calibrate USB serial?

    By jhumbeutel, February 7, 2011
    • 6 replies
    • 2,448 views
    • 
    • Dakotagrafx
    • February 16, 2011

12. Cutting roll paper

    By Biologyben, September 12, 2017   

    • roll paper
    • 3 replies
    • 2,440 views
    • 
    • MZ SKEETER
    • September 12, 2017

13. laserpoint cuts fine on right side of vinyl and not on the left side,help please

    By forsalevinylsigns, March 24, 2009
    • 17 replies
    • 2,416 views
    • 
    • CRD
    • June 19, 2009

14. Cutting Strip that fits

    By tomb321, March 22, 2010
    • 12 replies
    • 2,414 views
    • 
    • jaybyrd
    • February 27, 2014

15. How to check baud rate on Laserpoint?

    By JimmieD, February 1, 2008
    • 1 reply
    • 2,395 views
    • 
    • kenimes
    • February 1, 2008

16. 1 cutter, 2 computers?

    By cbgcustomgifts, August 13, 2017   

    • 2 computers
    • usb
    • 12 replies
    • 2,361 views
    • 
    • cbgcustomgifts
    • August 15, 2017

17. Laser point 3 wobble cut & more issues plz help

    By vixencharm, October 14, 2020
    • 19 replies
    • 2,361 views
    • 
    • slice&dice
    • December 18, 2020

18. Two silver endcaps with stand

    By Resilient, April 28, 2011
    • 10 replies
    • 2,350 views
    • 
    • AshComputers
    • April 30, 2011

19. LP II Serial Setup

    By CarterMarkham, September 30, 2012
    • 6 replies
    • 2,346 views
    • 
    • CarterMarkham
    • October 3, 2012

20. R u using a Laserpoint 24 and SignCut in So. CA?

    By cornball, May 22, 2010
    • 12 replies
    • 2,333 views
    • 
    • CRD
    • June 21, 2010

21. Cutter Freezing up

    By Debra Payne, October 6, 2010
    • 9 replies
    • 2,328 views
    • 
    • CRD
    • October 8, 2010

22. I need help closing the gaps and corners.

    By Rockon100, September 6, 2009
    • 22 replies
    • 2,316 views
    • 
    • Rockon100
    • September 7, 2009

23. Laserpoint2 doesnt complete job

    By D!0N, May 8, 2018
    • 21 replies
    • 2,308 views
    • 
    • MrXray
    • June 16, 2020

24. Vinyl off tracking

    By Kysmiley, July 9, 2008
    • 23 replies
    • 2,281 views
    • 
    • Danieve
    • November 19, 2008

25. lp2 contour cuttin with scal pro 3

    By jaybyrd, April 10, 2013
    • 8 replies
    • 2,277 views
    • 
    • Smalibu046
    • April 10, 2016