GraphTec Cutting Plotter Support Requests

368 topics in this forum

1. Craft Robo to cut monogram

   By ahood, October 31, 2012
   • 2 replies
   • 1,550 views
   • 
   • edge
   • October 31, 2012

2. CraftRobo CC330-20

   By serg33, March 16, 2012
   • 3 replies
   • 3,203 views
   • 
   • vinylmotivations
   • July 20, 2012

3. Crazy crosscut problems after job is done

   By ClearG, August 11, 2019
   • 1 reply
   • 1,072 views
   • 
   • Dakotagrafx
   • August 11, 2019

4. Cut Master 4 License

   By Irv J, January 15, 2019
   • 8 replies
   • 3,657 views
   • 
   • Irv J
   • January 17, 2019

5. Cut through on the Graphtec CE6000-60?

   By YerrytheYanitor, June 10, 2021
   • 2 replies
   • 826 views
   • 
   • darcshadow
   • June 10, 2021

6. Cutter blade always in the down position

   By tryto, July 19, 2008
   • 7 replies
   • 4,215 views
   • 
   • MZ SKEETER
   • November 30, 2011

7. Cutter not listed in Grapthec Studio software

   • 1
   • 2

   By AkeeLaMor, March 15, 2020
   • 33 replies
   • 3,353 views
   • 
   • MZ SKEETER
   • March 15, 2020

8. Cutting 0.12mm mylar

   By Arveisme, May 23, 2020
   • 4 replies
   • 1,371 views
   • 
   • haumana
   • May 24, 2020

9. Cutting Default Settings

   By darcshadow, June 17, 2023
   • 0 replies
   • 745 views
   • 
   • darcshadow
   • June 17, 2023

10. Cutting issue CE6000

    By A_Pola, October 1, 2017
    • 18 replies
    • 5,597 views
    • 
    • haumana
    • April 7, 2021

11. Cutting Master 2 1.4v and 1.6v issues on Illustrator or CorelDraw

    By Sandstormdesigns, March 31, 2009
    • 5 replies
    • 3,745 views
    • 
    • Renegade
    • April 17, 2009

12. Cutting Master 3 cannot find my Cutter

    By BFCD, February 6, 2018   

    • graphtec ce6000-40 plus
    • graphtec
    • (and 3 more)

      Tagged with:

      • graphtec ce6000-40 plus
      • graphtec
      • cutting master 3
      • ce6000-40 plus
      • missing cutter
    • 0 replies
    • 2,318 views
    • 
    • BFCD
    • February 6, 2018

13. cutting master and corel

    By DTFuqua, November 22, 2008
    • 9 replies
    • 2,531 views
    • 
    • Budsoda
    • February 28, 2009

14. Cutting OUTLINE ONLY using Cutting Master 2 from Corel X3

    By Sunrise Andy, June 30, 2008
    • 0 replies
    • 1,598 views
    • 
    • Sunrise Andy
    • June 30, 2008

15. Cutting Problem

    By Sharon, January 28, 2011
    • 2 replies
    • 1,542 views
    • 
    • MZ SKEETER
    • January 28, 2011

16. Cutting problem graphtic 6000 plus

    By NWORK57, January 12, 2021
    • 7 replies
    • 744 views
    • 
    • haumana
    • January 16, 2021

17. cutting vinyl letters on Graphtec Craft Robo Pro

    By ldrcgraphics, June 21, 2010
    • 1 reply
    • 3,270 views
    • 
    • Tom@USCutter
    • June 29, 2010

18. Cutting X+ Direction Uneven - CE7000-60

    • 1
    • 2

    By levy4u, July 23, 2021
    • 36 replies
    • 4,384 views
    • 
    • Dakotagrafx
    • December 13, 2021

19. Design Position Way Off

    By webcat, September 10, 2021
    • 12 replies
    • 949 views
    • 
    • MZ SKEETER
    • September 11, 2021

20. Difference between HP-GL and GP-GL

    By James159, January 20
    • 3 replies
    • 223 views
    • 
    • James159
    • January 21

21. downloading fonts

    By Kgrossman, April 7, 2020
    • 10 replies
    • 2,029 views
    • 
    • bethann
    • May 4, 2020

22. e05004 Error after new Motherboard Installed

    By JRV616, August 8, 2017   

    • e05004
    • error
    • (and 3 more)

      Tagged with:

      • e05004
      • error
      • ce6000
      • motherboard
      • install
    • 0 replies
    • 2,150 views
    • 
    • JRV616
    • August 8, 2017

23. factory reset fc8000

    By khalod, July 12, 2017
    • 2 replies
    • 4,177 views
    • 
    • Jburns
    • July 12, 2017

24. FC 7000 issue

    By bradqr1954, April 8, 2016
    • 7 replies
    • 1,670 views
    • 
    • Wildgoose
    • April 10, 2016

25. FC-8600 not completing cuts

    By mistwist, July 5, 2023
    • 1 reply
    • 801 views
    • 
    • Wildgoose
    • July 5, 2023