GraphTec Cutting Plotter Discussion

484 topics in this forum

1. Craft Robo Info

   By BannerJohn, September 18, 2008
   • 5 replies
   • 11,410 views
   • 
   • aguilar
   • October 18, 2022

2. info from graphtec for cutmaster 3 and Graphtec studio

   By Dakotagrafx, January 23, 2017
   • 4 replies
   • 5,091 views
   • 
   • Dakotagrafx
   • January 26, 2017

3. Graphtec CE7000 Push Rollers

   • 1
   • 2
   • 3
   • 4

   By ECombs, July 19, 2020
   • 99 replies
   • 11,619 views
   • 
   • slice&dice
   • May 21, 2023

4. Q42 cutting small letters issues

   • 1
   • 2
   • 3
   • 4

   By Kstill2671, January 24, 2019
   • 76 replies
   • 5,875 views
   • 
   • MZ SKEETER
   • January 25, 2019

5. New to vinyl. Just got a fc 7000 75

   • 1
   • 2
   • 3

   By Lorne D. Manor., May 13, 2019
   • 61 replies
   • 5,391 views
   • 
   • MZ SKEETER
   • May 31, 2019

6. Graphtec CE6000-60 Firmware

   • 1
   • 2
   • 3

   By Appleuser, February 5, 2015
   • 60 replies
   • 22,496 views
   • 
   • hkarns712
   • February 9, 2019

7. Graphtec CE5000

   • 1
   • 2
   • 3

   By ramy, August 25, 2010
   • 55 replies
   • 9,425 views
   • 
   • Rodger
   • June 1, 2011

8. About to buy new CE6000-60

   • 1
   • 2
   • 3

   By theishkid, January 13, 2013
   • 52 replies
   • 15,618 views
   • 
   • Dakotagrafx
   • May 12, 2014

9. CE5000 vs CE6000

   • 1
   • 2
   • 3

   By JHew84, December 19, 2013
   • 51 replies
   • 13,578 views
   • 
   • Ninja
   • May 27, 2014

10. Ce6000-60 Perf Cut just cutting solid paths

    • 1
    • 2
    • 3

    By levy4u, December 13, 2014
    • 50 replies
    • 14,813 views
    • 
    • MZ SKEETER
    • January 11, 2015

11. Cutting with CE 6000 plus

    • 1
    • 2

    By KDM_Freak, June 8, 2018
    • 47 replies
    • 4,993 views
    • 
    • darcshadow
    • June 11, 2018

12. How to check used Graphtec

    • 1
    • 2

    By WildCorral, October 29, 2021
    • 41 replies
    • 3,075 views
    • 
    • WildCorral
    • November 18, 2021

13. FC8600 not cutting small stuff properly

    • 1
    • 2

    By TimEdwards888, December 9, 2015
    • 40 replies
    • 7,428 views
    • 
    • TimEdwards888
    • December 15, 2015

14. Graphtec Question

    • 1
    • 2

    By bethfuciu, October 11, 2017
    • 37 replies
    • 6,263 views
    • 
    • Dakotagrafx
    • October 15, 2017

15. Cutting Problem Graphtec CE6000-60

    • 1
    • 2

    By Worble7, November 9, 2021
    • 37 replies
    • 2,676 views
    • 
    • Dakotagrafx
    • January 16, 2022

16. Cutter wont work on new computer...

    • 1
    • 2

    By gcextreme, March 16, 2015
    • 36 replies
    • 10,044 views
    • 
    • MZ SKEETER
    • March 18, 2015

17. Graphtec repair question

    • 1
    • 2

    By xpaperman, June 12, 2013
    • 35 replies
    • 5,452 views
    • 
    • jaybyrd
    • July 24, 2013

18. CE6000-60 Newbie issues, Curves & Cut Controller

    • 1
    • 2

    By terranomade, September 27, 2015
    • 35 replies
    • 15,071 views
    • 
    • MZ SKEETER
    • November 27, 2017

19. Alignment marks as to line up multiple vinyl

    • 1
    • 2

    By Worble7, October 18, 2021
    • 34 replies
    • 2,859 views
    • 
    • haumana
    • December 5, 2021

20. Best way to lineup vinyl on a CE5000?

    • 1
    • 2

    By firemalt, May 7, 2009
    • 33 replies
    • 5,833 views
    • 
    • Guest fivestar
    • June 13, 2009

21. Graphtec ce 5000-40 Not syncing with cutting master 3

    • 1
    • 2

    By yetna, April 17, 2015
    • 32 replies
    • 27,483 views
    • 
    • MZ SKEETER
    • April 30, 2017

22. Graphtec Craft Robo Pro issues

    • 1
    • 2

    By top53, July 21, 2015
    • 31 replies
    • 5,244 views
    • 
    • decalfarm
    • August 7, 2020

23. full sticker cutting / tool position

    • 1
    • 2

    By elpelon, March 23, 2019
    • 30 replies
    • 6,077 views
    • 
    • Dakotagrafx
    • April 28, 2019

24. GraphTec offset problems

    • 1
    • 2

    By sidxyz1, January 5, 2011
    • 29 replies
    • 12,583 views
    • 
    • NiteWalker
    • February 16, 2011

25. New Graphtec 6000-60; having trouble setting it up...

    • 1
    • 2

    By PhaedrusZen, February 22, 2015
    • 29 replies
    • 4,658 views
    • 
    • Dakotagrafx
    • March 23, 2018