GraphTec Cutting Plotter Support Requests

368 topics in this forum

1. Ce6000-60plus issues

   By arroncollins, February 28, 2019
   • 24 replies
   • 2,469 views
   • 
   • Dakotagrafx
   • March 6, 2019

2. CE6000, some awesomeness and some frustration

   By motoxchic, February 24, 2013
   • 0 replies
   • 877 views
   • 
   • motoxchic
   • February 24, 2013

3. CE7000 - "Please Send Firmware"

   By bob-le-bob, November 2, 2020
   • 12 replies
   • 1,790 views
   • 
   • MZ SKEETER
   • December 1, 2020

4. CE7000 Curves not cutting properly - choppy

   • 1
   • 2

   By NTBVinyls, June 17, 2021
   • 34 replies
   • 5,420 views
   • 
   • darcshadow
   • July 30, 2022

5. CE7000 Double cutting

   By Hawaii Kai, March 30, 2021
   • 8 replies
   • 2,121 views
   • 
   • Wildgoose
   • April 4, 2021

6. ce7000 not cutting some nodes

   By lilone2j, March 11, 2021   

   • graphtec studio
   • 10 replies
   • 914 views
   • 
   • lilone2j
   • March 18, 2021

7. CE7000 Not Sensing Back Reg Marks

   By SethT., February 14, 2023
   • 1 reply
   • 556 views
   • 
   • MZ SKEETER
   • February 14, 2023

8. CE7000-60 Contour Cutting Help

   By Stephen H., November 2, 2020   

   • contour cutting
   • ce7000-60
   • 2 replies
   • 975 views
   • 
   • Dakotagrafx
   • November 3, 2020

9. CE7000-60 contour cutting issues

   By Kuchyyz, December 7, 2020
   • 4 replies
   • 811 views
   • 
   • haumana
   • December 7, 2020

10. CE7000-60 test cut pattern not square

    By Choppy, February 19, 2023
    • 15 replies
    • 1,613 views
    • 
    • kainth.c.s
    • February 20, 2023

11. Cleancut Tool setting

    By Madam_x, August 10, 2018   

    • cleancut
    • clean cut
    • (and 2 more)

      Tagged with:

      • cleancut
      • clean cut
      • tool setting
      • graphtec
    • 11 replies
    • 2,782 views
    • 
    • Madam_x
    • August 20, 2018

12. CM3 for osx Mavericks???

    By redlinegraphics, February 7, 2014
    • 6 replies
    • 1,527 views
    • 
    • jarrotto
    • February 23, 2014

13. Complete failure to "Turn On" CE5000-40 CRP

    By Adam Walker, October 7, 2008
    • 2 replies
    • 1,783 views
    • 
    • Adam Walker
    • October 8, 2008

14. Completing cut

    By Twiz89, May 2, 2013
    • 6 replies
    • 1,295 views
    • 
    • Twiz89
    • May 2, 2013

15. Configure Cut Job

    By Wygal, December 10, 2016
    • 0 replies
    • 909 views
    • 
    • Wygal
    • December 10, 2016

16. Connecting a Graphtec fc4100-75 to a windows vista

    By doodman, July 6, 2009
    • 5 replies
    • 3,958 views
    • 
    • doodman
    • October 27, 2009

17. connection

    By mustangconv85, December 21, 2008
    • 8 replies
    • 2,500 views
    • 
    • Guest
    • December 24, 2008

18. contour cut and signmaster 2 cutting error?

    By han7681, May 27, 2012
    • 0 replies
    • 1,243 views
    • 
    • han7681
    • May 27, 2012

19. contour cutting

    By wissam, June 19, 2013
    • 1 reply
    • 1,055 views
    • 
    • mopar691
    • June 19, 2013

20. Contour Cutting / Reading Marks with SignCut Pro & Graphtec

    By twhite, February 11, 2015
    • 0 replies
    • 1,545 views
    • 
    • twhite
    • February 11, 2015

21. Contour cutting CE5000 W/cutting master 2

    By Dr Smith, May 24, 2010
    • 4 replies
    • 1,744 views
    • 
    • Dr Smith
    • May 28, 2010

22. Contour cutting without registration marks? Graphtec FC8600

    By Emanuelle, October 9, 2018
    • 6 replies
    • 2,515 views
    • 
    • Emanuelle
    • October 10, 2018

23. Corel X4

    By Sunrise Andy, June 24, 2008
    • 1 reply
    • 1,910 views
    • 
    • kenimes
    • June 24, 2008

24. Craft Robo 330L-20 Easy Question (width of vinyl help)

    By gasper44, January 28, 2010
    • 7 replies
    • 1,455 views
    • 
    • edge
    • January 30, 2010

25. craft robo doesn't read registration marks and get port read error

    By freebird1963, October 23, 2009
    • 0 replies
    • 1,620 views
    • 
    • freebird1963
    • October 23, 2009