Search the Community
Showing results for tags 'calibration'.
Found 8 results
Can't manage to calibrate KH 720
Johnterry52 posted a topic in USCutter Refine Cutting Plotter DiscussionHello, I'm posting in this section because I can't find any other place. I have the vinyl cutter kh-720 with the sign master V3.5 software but I've been trying to configure it for 3 days without success. I can't calibrate it, I try with A4 sheets but there is always an offset of about 1 cm (I tried checking and uncheking offset). I have searched all google and youtube but no luck. Anyone have a tuto to show me please?
Calibration File for this device cannot be found
Clockmans posted a topic in VinylMaster CUT, LTR, PRO & DSRSo I just set up vinyl master on a new computer but cannot get this machine to calibrate. When I go to lasser offset full it says it can not find the Calibration File for this device. Also when I go to calibrate the arms offset it will not detect all the marks and I have tried and tried again and again. I am running a titan 3 along with vinylmaster pro. If anyone can help me it would be much appreciated.
VM Cut with Titan 3 15" contour cut calibration
Guest posted a topic in VinylMaster CUT, LTR, PRO & DSRI have VinylMaster Cut. Titan 3 cutter. Trying to use contour cutting. But the cut is way off. I have tried time and time again to "calibrate" so that it cuts correctly. How do I set this up so it cuts correctly?? I am sick and tired of the lack of support for both this cutter AND VinylMaster Cut. Can anyone help?? Guide me to get this calibrated?? Arrgghhh!
Relationship between Jog Settings vs. X and Y Scale
EAWF posted a topic in Creation PCUT Cutting Plotter DiscussionHas anyone worked out the mathematical relationship between a cutters jog settings and the X_Scale / Y_Scale settings? There has to be some kind of relationship, and it would be nice to know if the cutter could be calibrated to produce more accurate lengths and widths without having to guess. Thanks in advance for your expert and prompt response.
Heat Press 3802 clam shell lid
bakerchick posted a topic in Heat PressesHello, Total newbie here. I am not understanding how to calibrate my heat press. I know I set the temp to 380 and with it reaches 100 I am to press the down arrow for 5 seconds. How am I to tell if the machine is in calibration mode? My instructions say the calibration should take around 20 minutes. How will I know when the calibration is complete? Thank you!!
calibration all of a sudden is off
Guest posted a topic in VinylMaster CUT, LTR, PRO & DSRI purchase my vinyl master 4 this morning. I cut many designs with it since I was way behind in my work. I noticed one thing wasn't quite right so I went to the calibration area to see what it said. Now it is cutting Everything 4 times it's accurate size. If I try and cut the "test cut" in the calibration it says it is a bit over 7" x 9" but it is trying to cut a rectangle over 3' tall. I cannot figure out how to fix this and it is making me think I made a mistake in purchasing the software. I only use the software to get my illustrator designs to the plotter as I do all my designing in illustrator. Please help, I am stuck until I figure this out
Issues with Titan 2
houstonwehaveaproblem posted a topic in TITAN Series Vinyl Cutter DiscussionsI have an email in with us cutters right now, just waiting on a reply. While I wait I would like to find out if anyone else has been experiencing the same issues. I am not new to vinyl cutters, I have been using them the last few years so this isn't my first set up. I followed all the directions on start pdf too, just to be on the safe side. Up until last week I have been using a laser point 2, with SCAL3 e Now on with the problem. the machine is set up. I have vinyl master installed. correct driver is installed. I open an SVG saved from AI, try to cut and it does not cut correctly, it is 2'x2' and instead of cutting across the cutter it is making small cuts at the origin then spooling 2' of material and making a few small cuts and bouncing back and fourth. I cancel the cut try and rotate the image a few different times and nothing is working. I then say screw it and let it go. after about 8-10 minutes in the cutter starts to overlap the image and I have to cancel the cut. I try tracing the image in vinyl master and I get the same effect. keep in mind this is the same file I've used in SCAL over the past year on the laser point. I try all the calibration options in vinylmaster multiple times. I give up with vinylmaster and open SCAL 3. I load the Titan 2 into "my cutter" and bring up a SCAL file that I always use and know it to work on the laser point. The cut order is much better and it seems like it is cutting smoothly. The issue is when I go to weed my project there are gaps in some areas and overlap in others. I cut a second sheet before I picked the first, the second has the same issues however the gaps and overlaps are not in the same place. they are located in different areas. I am beginning to think it is the offset of the cutter or possibly the cutter is a lemon... I'm not sure, hopefully USC will fix me up and I can get back to business. If anyone else has any tips Please help me out. Being without my vinyl cutter feels very weird, and I have orders coming in that I have to refuse or have an extremely log wait time.
new to this and need some help
no7h1ng posted a topic in Sure Cuts A Lot ProI just got my laserpoint 2 cutter last week, and i'm trying to calibrate the laser for it on sure cuts a lot pro. after it does the little crosshair it doesn't turn the laser on so i can align it. is there a setting for this? i know i can turn the laser on manually going thru local - then on with the cutter itself but then i cant adjust it in the software. any help would be great! thank you