TITAN 2 Series Vinyl Cutter Discussions

165 topics in this forum

1. Titan 2 Connection issues

   By VisualExpressionsNJ, August 15, 2020
   • 2 replies
   • 1,925 views
   • 
   • slice&dice
   • August 15, 2020

2. Can i have my setup on carpet?

   By Sarjento956, July 24, 2020
   • 5 replies
   • 1,440 views
   • 
   • Scratchthejeepguy
   • July 24, 2020

3. Used Titan 2

   By Sam_Beckett, July 8, 2020   

   • titan2
   • used
   • (and 1 more)

     Tagged with:

     • titan2
     • used
     • titan 2
   • 13 replies
   • 1,633 views
   • 
   • Wildgoose
   • July 10, 2020

4. Over Size Please Reset!

   By RRS1983, June 10, 2020
   • 2 replies
   • 1,670 views
   • 
   • MZ SKEETER
   • June 10, 2020

5. Vinyl Cutting Software Recommendations

   By matt12, May 4, 2020
   • 3 replies
   • 1,463 views
   • 
   • Wildgoose
   • May 5, 2020

6. Probably nitpicking here but...(Cutting finished vinyl from roll after design is cut)

   By Cliff P, May 1, 2020
   • 10 replies
   • 1,494 views
   • 
   • Cliff P
   • May 2, 2020

7. Cutting letter format (8.5x11") sheets on my 28" Titan 2

   By Cliff P, April 29, 2020
   • 3 replies
   • 1,118 views
   • 
   • MZ SKEETER
   • April 29, 2020

8. 45 degree blade offset

   By GHEENEE1, April 9, 2020
   • 4 replies
   • 1,924 views
   • 
   • haumana
   • April 9, 2020

9. Anyone know what overcut is?

   By mpanek, March 5, 2020
   • 10 replies
   • 2,230 views
   • 
   • Dakotagrafx
   • March 5, 2020

10. vectors

    By Strikenmike, February 14, 2020
    • 1 reply
    • 982 views
    • 
    • bikemike
    • February 14, 2020

11. Configuration conflict

    By Strikenmike, January 25, 2020
    • 9 replies
    • 1,448 views
    • 
    • haumana
    • January 26, 2020

12. Titan2 leftmost pinch roller not in sync?

    By handmadelovely, December 27, 2019
    • 3 replies
    • 1,051 views
    • 
    • slice&dice
    • December 28, 2019

13. Titan 2 not cutting correctly

    • 1
    • 2

    By jamiefeld, October 9, 2019
    • 34 replies
    • 4,979 views
    • 
    • Caseman315
    • December 22, 2019

14. Titan2 Issues

    By Eazy, December 1, 2019
    • 8 replies
    • 1,252 views
    • 
    • Eazy
    • December 3, 2019

15. titan 2 cutting issues

    By Daveischosen, November 5, 2019   

    • titan2
    • cutting issues
    • 7 replies
    • 1,957 views
    • 
    • Wildgoose
    • November 8, 2019

16. DRV Error

    By JC4, April 25, 2017   

    • titan 2
    • drv
    • (and 6 more)

      Tagged with:

      • titan 2
      • drv
      • error
      • wont cut
      • restart power message
      • driver
      • driver error message
      • error message
    • 21 replies
    • 7,571 views
    • 
    • Dakotagrafx
    • October 30, 2019

17. Titan 2 cuts super slow on a specific design

    By marquezjc, September 27, 2019
    • 11 replies
    • 1,027 views
    • 
    • slice&dice
    • September 27, 2019

18. Mimaki CJ 150 prints to cut on Titan ll

    By Johnmpcny, September 12, 2019
    • 8 replies
    • 1,267 views
    • 
    • Dakotagrafx
    • September 13, 2019

19. Blade holder will not raise up

    By ryugaiden05, August 3, 2019
    • 6 replies
    • 926 views
    • 
    • ryugaiden05
    • August 8, 2019

20. Help!! Magnet cutting, machine hard to calibrate

    • 1
    • 2
    • 3
    • 4
    • 7

    By Kristof, June 15, 2019
    • 157 replies
    • 10,101 views
    • 
    • Buggie Pilot
    • August 6, 2019

21. Help with VM Ltr

    By bigmax, August 4, 2019
    • 2 replies
    • 810 views
    • 
    • Wildgoose
    • August 4, 2019

22. Cut strip

    By GHEENEE1, June 29, 2019
    • 4 replies
    • 976 views
    • 
    • Dakotagrafx
    • June 29, 2019

23. Mr Thompson

    By vernil thompson, June 22, 2019
    • 2 replies
    • 1,000 views
    • 
    • Dakotagrafx
    • June 22, 2019

24. Upgrade Question

    By rdunn12, March 12, 2019
    • 7 replies
    • 1,280 views
    • 
    • darcshadow
    • March 12, 2019

25. Titan 2 mother board install

    By Scotts Games, February 27, 2019
    • 6 replies
    • 1,324 views
    • 
    • haumana
    • February 27, 2019