GraphTec Cutting Plotter Discussion

484 topics in this forum

1. Got my new ce6000 working great just 1 question

   By paz21paz, December 11, 2013
   • 11 replies
   • 2,549 views
   • 
   • mr300s
   • January 22, 2014

2. god is good scored a graphtec ce 5000 -60

   By djque, July 9, 2014
   • 11 replies
   • 1,149 views
   • 
   • Sue2
   • July 28, 2014

3. My New (to me:) FC7000MK2-100

   By Jburns, December 8, 2014
   • 11 replies
   • 1,222 views
   • 
   • Jburns
   • December 8, 2014

4. Graphtec

   By jdmarti1, September 30, 2015
   • 11 replies
   • 1,677 views
   • 
   • djque
   • October 4, 2015

5. What Maintenance to do CE5000

   By Izzy11, October 10, 2015
   • 11 replies
   • 3,547 views
   • 
   • Dakotagrafx
   • October 14, 2015

6. Thinking about buying from Alibaba - do fakes exist?

   By Trillion, December 7, 2015
   • 11 replies
   • 1,664 views
   • 
   • Trillion
   • December 11, 2015

7. First test cuts with my first cutter CE6000-60 Plus. Any tips, tricks or advice for a newbie?

   By Mugiwara, May 7, 2018
   • 11 replies
   • 1,986 views
   • 
   • haumana
   • May 8, 2018

8. FC8000-60 Corner Issues

   By MCobb, August 15, 2018   

   • fc8000-60
   • 11 replies
   • 2,031 views
   • 
   • MZ SKEETER
   • August 15, 2018

9. Graphtec FC-8000 Problems

   By MSellers15, July 10, 2020
   • 11 replies
   • 1,977 views
   • 
   • Dakotagrafx
   • July 16, 2020

10. Start and finish points does not align

    By winslo93, December 30, 2021
    • 11 replies
    • 1,675 views
    • 
    • MZ SKEETER
    • February 7, 2023

11. Cutting Master 5 Contour cutting is not supported for multi-page design

    By UO-Jeremy, September 7, 2023   

    • grpahtec
    • cutting master 5
    • (and 3 more)

      Tagged with:

      • grpahtec
      • cutting master 5
      • error
      • contour cut
      • contour
    • 11 replies
    • 1,297 views
    • 
    • haumana
    • September 18, 2023

12. Loving my new Graphtec

    By duck1973, January 6, 2011
    • 10 replies
    • 2,142 views
    • 
    • duck1973
    • January 19, 2011

13. Replacing Cutting Strip

    By mingle, February 15, 2011
    • 10 replies
    • 2,541 views
    • 
    • LogoCrazy
    • January 31, 2012

14. Graphtec Contour-Cutting on Reflective Vinyl?

    By NukleoN, March 8, 2011
    • 10 replies
    • 3,929 views
    • 
    • NukleoN
    • March 14, 2011

15. cuts all over my "bar"

    By motoxchic, March 24, 2013
    • 10 replies
    • 1,757 views
    • 
    • Dakotagrafx
    • March 25, 2013

16. Do I need this?

    By xpaperman, June 7, 2013
    • 10 replies
    • 1,069 views
    • 
    • Dakotagrafx
    • June 8, 2013

17. How small is too small with a CE6000

    By iamandy, April 11, 2014
    • 10 replies
    • 1,702 views
    • 
    • rlvied
    • April 12, 2014

18. CE5000 and Cutting Master3: Another Problem

    By skorper, July 1, 2014
    • 10 replies
    • 1,029 views
    • 
    • MZ SKEETER
    • July 2, 2014

19. Graphtec advance amount after copy???

    By MrJoel, October 19, 2019
    • 10 replies
    • 1,508 views
    • 
    • MrJoel
    • October 20, 2019

20. Settings seem off

    By 3 Kells Design, May 1, 2021
    • 10 replies
    • 1,146 views
    • 
    • haumana
    • May 3, 2021

21. Vinyl bowing issue

    By Robert2495, August 30, 2021   

    • plotter
    • graphtec ce6000-60
    • (and 2 more)

      Tagged with:

      • plotter
      • graphtec ce6000-60
      • vinyl
      • bowing
    • 10 replies
    • 1,001 views
    • 
    • Robert2495
    • October 11, 2021

22. Cutting Master 5 not cutting outer edges

    By UO-Jeremy, November 21, 2023   

    • graphtec
    • cutting master 5
    • (and 1 more)

      Tagged with:

      • graphtec
      • cutting master 5
      • ventura
    • 10 replies
    • 785 views
    • 
    • UO-Jeremy
    • December 18, 2023

23. Craft Robo CC330L-20 cutting .13mm Velum

    By Spike, August 21, 2009
    • 9 replies
    • 2,568 views
    • 
    • dbtoutfit
    • September 15, 2009

24. Doing some research!

    By Cre8tiveCutter, September 13, 2009
    • 9 replies
    • 1,694 views
    • 
    • MZ SKEETER
    • September 14, 2009

25. arms upgrade

    By jaybyrd, June 7, 2013
    • 9 replies
    • 1,639 views
    • 
    • jaybyrd
    • June 7, 2013