USCutter Refine Cutting Plotter Discussion

811 topics in this forum

1. MH-365

   By gpau, January 8, 2013
   • 0 replies
   • 1,001 views
   • 
   • gpau
   • January 8, 2013

2. Switching from USB to Serial-USB connection on MH721, getting error

   By blackpaws, January 3, 2013
   • 9 replies
   • 4,251 views
   • 
   • slice&dice
   • January 4, 2013

3. contour cutting without a laser light

   By daimagic, January 1, 2013
   • 3 replies
   • 1,302 views
   • 
   • MZ SKEETER
   • January 1, 2013

4. Can an MH-871 cut magnet sheets?

   By JHew84, December 9, 2012
   • 7 replies
   • 4,773 views
   • 
   • JHew84
   • December 17, 2012

5. Changed to serial, can't get SC to work now.

   By imaseahawksfan, October 16, 2012
   • 8 replies
   • 1,943 views
   • 
   • Monkey
   • December 8, 2012

6. MH871 won't cut...then hits red button on side.

   By Squewheet, November 16, 2012
   • 6 replies
   • 2,224 views
   • 
   • Squewheet
   • November 21, 2012

7. Serial port Cable?

   By randyb, November 16, 2012
   • 2 replies
   • 1,459 views
   • 
   • randyb
   • November 16, 2012

8. I hate to make another thread, but...

   By Rob@MM, November 1, 2012
   • 5 replies
   • 1,203 views
   • 
   • vinylmotivations
   • November 2, 2012

9. MH 721-MK2 Cutting Problems

   By bigrapidstrophies, October 9, 2012   

   • Not Responding
   • Never-ending Lines
   • 1 reply
   • 3,235 views
   • 
   • Jay2703
   • October 9, 2012

10. Cutting Strip on MH721

    By xJoey Dubsx, October 12, 2010
    • 5 replies
    • 2,944 views
    • 
    • Fred Kaz
    • September 30, 2012

11. MH 871 Problems

    By sluggo2u, June 16, 2012
    • 5 replies
    • 4,972 views
    • 
    • Pcrat
    • September 22, 2012

12. refine 28" drivers

    By philstubbs, September 4, 2012
    • 4 replies
    • 1,607 views
    • 
    • philstubbs
    • September 13, 2012

13. I love my MH 871, never a problem, just need new blades after a year...

    By T3rry, September 1, 2012
    • 5 replies
    • 1,522 views
    • 
    • MZ SKEETER
    • September 1, 2012

14. Y axis freaking out!!!

    By highonlif, August 23, 2012
    • 8 replies
    • 2,659 views
    • 
    • Jay2703
    • August 24, 2012

15. mh721 cutting through design

    By egobuster1, July 11, 2012
    • 9 replies
    • 2,187 views
    • 
    • Dr12volt1338
    • August 21, 2012

16. MH 721 Won't cut 90 degree angles cleanly

    By GuerillaGraphics, June 22, 2012
    • 4 replies
    • 1,742 views
    • 
    • highonlif
    • August 9, 2012

17. Refine MH721

    By bagmania01, August 5, 2012   

    • Refine Mh721
    • setup
    • 2 replies
    • 2,167 views
    • 
    • Jay2703
    • August 6, 2012

18. You guessed it, Mh 721 cutting problems..

    By ecto1, June 21, 2012
    • 9 replies
    • 5,341 views
    • 
    • slice&dice
    • July 27, 2012

19. mh1351 not cutting proper

    By crow11, May 24, 2011
    • 2 replies
    • 2,047 views
    • 
    • Mikelemazo
    • July 21, 2012

20. USB> Serial vs Installing Serial ports in PC

    By tweetlbug, July 11, 2012
    • 7 replies
    • 2,387 views
    • 
    • tweetlbug
    • July 12, 2012

21. Cutter misaligning weeding lines?

    • 1
    • 2

    By JennD26, July 8, 2012
    • 38 replies
    • 4,389 views
    • 
    • Coaster36
    • July 8, 2012

22. MH-721 computer requirements

    By JennD26, June 25, 2012
    • 3 replies
    • 1,106 views
    • 
    • JennD26
    • June 25, 2012

23. MH-721 blade issues?

    By JennD26, June 16, 2012
    • 8 replies
    • 3,668 views
    • 
    • JennD26
    • June 16, 2012

24. MH871 Problem

    By Exquisite Graphix, June 2, 2012
    • 11 replies
    • 2,119 views
    • 
    • locknload1
    • June 6, 2012

25. MH-721 Business

    By JennD26, June 3, 2012
    • 10 replies
    • 2,752 views
    • 
    • slice&dice
    • June 4, 2012