GraphTec Cutting Plotter Support Requests

368 topics in this forum

1. Help with FC2100-60a

   By JTairbrush, May 19, 2011
   • 22 replies
   • 13,380 views
   • 
   • Gaurav
   • January 18, 2014

2. Help! Ce-6000-60 cutting in slow motion.

   By bossman696, December 14, 2013
   • 9 replies
   • 4,831 views
   • 
   • jaybyrd
   • December 18, 2013

3. CE5000-60 How to advance to the next job

   By ajr2820, December 12, 2013
   • 3 replies
   • 1,163 views
   • 
   • mb20music
   • December 12, 2013

4. Text size always different when i cut On graphtec CE6000

   By JrVinyl, December 7, 2013
   • 1 reply
   • 1,879 views
   • 
   • jaybyrd
   • December 7, 2013

5. Graphtec CE5000 120 running SignBlazer

   By chefgary, March 21, 2013
   • 8 replies
   • 2,572 views
   • 
   • chefgary
   • November 26, 2013

6. contour cutting

   By wissam, June 19, 2013
   • 1 reply
   • 1,052 views
   • 
   • mopar691
   • June 19, 2013

7. Official Help paperman with Graphtec thread :-)

   By xpaperman, June 16, 2013
   • 13 replies
   • 2,351 views
   • 
   • jaybyrd
   • June 19, 2013

8. CE6000-60 FIrmware Update

   By eight2ten, May 11, 2013
   • 5 replies
   • 4,351 views
   • 
   • MZ SKEETER
   • May 12, 2013

9. Graphtec changing speed?

   • 1
   • 2

   By mfatty500, May 4, 2013
   • 29 replies
   • 6,561 views
   • 
   • MZ SKEETER
   • May 6, 2013

10. Completing cut

    By Twiz89, May 2, 2013
    • 6 replies
    • 1,293 views
    • 
    • Twiz89
    • May 2, 2013

11. Graphtec 2250 Table Surface Worn Out

    By plainblackguy, April 30, 2013
    • 0 replies
    • 843 views
    • 
    • plainblackguy
    • April 30, 2013

12. Graphtec FC8000 series - cuts choppy toward end of job

    By MidnightGlassworks, April 27, 2013
    • 24 replies
    • 3,898 views
    • 
    • Dakotagrafx
    • April 28, 2013

13. Graphtec ce6000-40

    By Ricktharula, April 27, 2013   

    • Trouble shoot
    • 2 replies
    • 2,075 views
    • 
    • Dakotagrafx
    • April 27, 2013

14. Why is 651 white fighting me so much?

    By Coaster36, April 17, 2013
    • 10 replies
    • 2,329 views
    • 
    • dwp99
    • April 18, 2013

15. Strange cut on CE6000-60

    • 1
    • 2

    By toddlamp, March 9, 2013
    • 25 replies
    • 11,496 views
    • 
    • MZ SKEETER
    • March 12, 2013

16. The tips of my A's are lifting, advice?

    • 1
    • 2

    By motoxchic, March 1, 2013
    • 30 replies
    • 4,278 views
    • 
    • motoxchic
    • March 7, 2013

17. CE6000, some awesomeness and some frustration

    By motoxchic, February 24, 2013
    • 0 replies
    • 874 views
    • 
    • motoxchic
    • February 24, 2013

18. CE5000-60 and Belkin Home Base

    By dolbyl, January 17, 2010
    • 2 replies
    • 2,912 views
    • 
    • southerndesigns
    • February 16, 2013

19. Help with graphtec fc7000-130

    By forsalevinylsigns, April 7, 2010
    • 11 replies
    • 4,678 views
    • 
    • eternalgraphics
    • February 12, 2013

20. Is my cutter dead?

    By allenallen, February 11, 2011
    • 12 replies
    • 4,120 views
    • 
    • eternalgraphics
    • February 9, 2013

21. New GraphTec CE-6000 40/60/120-amo Series

    By NichoDesign, January 7, 2013   

    • graphtec
    • graphtec 5000
    • (and 4 more)

      Tagged with:

      • graphtec
      • graphtec 5000
      • graphtec 6000
      • vinyl cutter
      • plotter
      • cutter
    • 3 replies
    • 4,519 views
    • 
    • NichoDesign
    • January 18, 2013

22. USED FC-5100 or NEW CE-5000?

    • 1
    • 2

    By theishkid, December 18, 2012
    • 28 replies
    • 7,641 views
    • 
    • Dakotagrafx
    • January 5, 2013

23. Graphtec ce5000 40cpr

    • 1
    • 2

    By Imlost21, November 13, 2012
    • 29 replies
    • 4,071 views
    • 
    • MZ SKEETER
    • November 14, 2012

24. Craft Robo to cut monogram

    By ahood, October 31, 2012
    • 2 replies
    • 1,548 views
    • 
    • edge
    • October 31, 2012

25. Graphtec F2100-50

    By ggmoreira, September 12, 2012   

    • Overcut and Cutter Offset
    • 2 replies
    • 1,290 views
    • 
    • ggmoreira
    • September 12, 2012