Leaderboard

Robin Williams committed suicide today. The news will cover it extensively. People who didn't know him will cry out that it's a major loss to them. On average, 23 Veterans will also commit suicide today, because the ravages ruined their mind. The news will NOT cover this. Nobody but the families will notice. Robin Williams starred in a movie about Vietnam. Many Veterans who will kill themselves served there. As you were.

I had these hats laying around I never really got into hats too much. These are nice hats but six panel which I found out weren't that great with vinyl because of the seam. I am going on a alligator hunt on a air boat sponsored by the Wounded Warriors Foundation the end of the Month , so I figured I would make everyone a hat. I am guessing they will like them especially since they are free...

Doing 10 of these for children' s Church

I have little respect or sampathy for anyone that takes their own life leaving all the pain that they could not bear for the loved ones to bear. He was a good actor but in my opinion took the cowards way out.

Get a professional to install it?

I have been on a mission lately to debug a problem I had with parts of my file not being cut. In summary, it wasn't static or memory but more likely Signcut Pro. I have a US Cutter Refine MH 721. I running XP and CorelDraw X4. I was using Signcut Pro but was having difficulties on larger file size cuts. It would skip over large portions. Sometimes it would just misbehave. So I grounded everything, didn't fix it. I bought the larger memory, didn't fix it. I installed Signblazer 6.05, fixed. Not exactly sure what the root cause is but has to do with how data is being transfered to the plotter. Signblazer 6.05 does not have the Refine drivers but I'm using RedSail RS720C which is working very well (note: The DMPL driver worked but the scaling was slightly larger than actual size (1"x1" was more like (1.01" x 1.01")). After all this research, I decided to make it more simple for newbies. If you want the latest and best version of Signblazer Elements with a crack that gets rid of trial mode, visit www.mystat.com and scroll down to the bottom. Also, we added a helpful user guide for MH series cutters that addresses grounding issues, loud printing, rip software and others: http://www.mystat.com/user-guide-tips-fixes-uscutter-mh.pdf cheers.

Here's a clue.... the point of it was the problem of veteran Suicide in general...which is barely covered by the media at all. Let's end it at that. I'm not going to have this turn into one of your famous 3 page discourses.

You missed the point entirely.

Unless you've been at the bottom of that hole you will never understand. There's a battle in you head that you can't figureout. You're overwelmed with sadness for no reason at all. I've been Very close to the bottom and being a coward isn't something you think about. To this day I can't understand what was going through my head but I did figure out a way to win the battle. You guys are like my Brother. He doesn't and can't understand what I went through. And like him I will tell you You'll never understand unless you've been there. Through everthing I found out my mother understood because she had been there also. That bond is what helped me out. I know one day the battle might start again but I know I'll be better prepared. I completely understand you have a right to your opionon. And I can understand why you would think that. but I don't agree with you.

mark-s

I usually always do a wet install with any lettering / graphics on vehicles. My routine is to clean with rubbing alcohol first (i have a spray bottle filled with it). Next i clean with Rapid Prep to remove any grease, wax, etc... Then i clean with rubbing alcohol again. I do all of my wet installs with Rapid Tac or Rapid Tac 2. I usually only use Rapid Tac 2 if its cold or very humid. I have never used the homemade application fluid solution, I tried using Splash application fluid and personally had a very difficult time with it. Then i tried Rapid Tac products and they have worked great for me so far. I order Rapid Tac products from Beacon Graphics since USCutter does not carry them... I wish they did. You might want to give them a shot. Good luck on your project.

Hmm kinda odd your going on a hunt for WW. When WW is anti-gun....? I boycott WW because of their stand on the 2nd Amendment. Tons of articles about it..here's one http://mynortheastoutdoors.com/wounded-warrior-program-ceo-confirms-group-is-anti-gun/

Scottty, You're Bad!!!!!!

hold it . . . you have a reflection? sorry carolyn couldn't resist

Nice job

Sounds like one of us should invest in a machine that custom cuts corro... then said person could supply us all with custom corro!

Is it one line of copy 3ft high or multiple lines of copy? I would cut into lengths that could be easily handled by one person and lay out the substrate with lines to keep all copy straight. This is assuming that you are installing to an existing structure.

I have my Avery chrome available, as I have to do a job. So I took some photos, I have my hand above the roll and a blue roll of vinyl beside it.. And you can also see my ceiling above. I couldn't get too close to the roll as it showed my reflection in it...LOL

Some kind of Celtic font mark-s

Not unless you have a very high end cutter. Graphtec FC series comes to mind. It uses a separate blade to cut off the vinyl once the job is done.

What kind of pads will I need for my 15 X 18 heat press? Where can I purchase them from and what else will I probably need? Thanx

Thanks guys appreciate the info! If anyone else has any suggestions please bring it.

Yeah I would try one minute and go down from there 5 seconds at a time until you find the sweet spot 400 degrees med to firm pressure ...

Actually it is more work to do an Etsy claim against a seller.. You have to mail everything in, with your proof, and their ads, to their offices in New York, and sign a penalty for perjury affidavit...I went thru that with a seller on Etsy, who was also a UScutter forum member... who got booted from here.( ) And I think Karma is still biting him in the A$$!!

I win!!!!! Found one. Tank Top Template.svg