Creation PCUT Cutting Plotter Support Requests

740 topics in this forum

1. BLADE HOLDER INSTRUCTIONS FOR P-CUT

   By BannerJohn, February 3, 2008
   • 19 replies
   • 16,096 views
   • 
   • KeystoneChuck
   • March 11, 2014

2. How to get support

   By BannerJohn, July 21, 2009
   • 0 replies
   • 8,629 views
   • 
   • BannerJohn
   • July 21, 2009

3. cutting with usb

   By jhelms, December 19, 2009
   • 9 replies
   • 1,470 views
   • 
   • jhelms
   • January 28, 2010

4. PCUT 630 (Can't cut more than 1 at a time w/out machine stopping) Fonts!

   By BLKSUNSHINE, April 3, 2009
   • 5 replies
   • 1,153 views
   • 
   • kenimes
   • April 14, 2009

5. "Corners" lifting

   By kst8catfan, September 2, 2008
   • 4 replies
   • 1,135 views
   • 
   • kst8catfan
   • September 4, 2008

6. "USB Device Malfunction"

   By DBR, May 8, 2008
   • 10 replies
   • 2,046 views
   • 
   • kenimes
   • May 9, 2008

7. "Waiting"

   By Chalyons3, April 29, 2008
   • 6 replies
   • 1,373 views
   • 
   • kenimes
   • May 5, 2008

8. ****PCUT freeze up, USB FIX #2****

   By protek, April 19, 2008
   • 5 replies
   • 1,292 views
   • 
   • protek
   • April 19, 2008

9. *Update* USB Not Acknowledged

   By imsracing, February 26, 2008
   • 8 replies
   • 1,364 views
   • 
   • kenimes
   • February 29, 2008

10. 110volt or 220volt?

    By riribarr, July 8, 2008
    • 5 replies
    • 987 views
    • 
    • riribarr
    • July 10, 2008

11. 230-250 micron thick is too heavy for PCUT 1200?

    By Aromo, June 3, 2009
    • 1 reply
    • 887 views
    • 
    • mars
    • July 26, 2009

12. 2nd bad motherboard

    By Karl, August 6, 2010
    • 3 replies
    • 1,533 views
    • 
    • Dakotagrafx
    • August 7, 2010

13. A bit of HELP needed

    By DUTCH, March 25, 2009
    • 1 reply
    • 848 views
    • 
    • kenimes
    • March 26, 2009

14. A couple of issues and inputs for Creation PCUT CT 630

    By kainth.c.s, November 7, 2016   

    • problems encounterred while cutting and support requests
    • 3 replies
    • 1,932 views
    • 
    • kainth.c.s
    • November 8, 2016

15. A few newb questions and problems here

    By blaster2001, October 10, 2008
    • 2 replies
    • 950 views
    • 
    • blaster2001
    • October 10, 2008

16. advise needed

    By stuart, January 9, 2009
    • 4 replies
    • 831 views
    • 
    • stuart
    • January 11, 2009

17. ahhhh not "waiting" in the middle of the cut again!!!!!

    By KrunkuliticusIII, July 2, 2008
    • 9 replies
    • 1,135 views
    • 
    • Knobhill
    • July 5, 2008

18. alignment issue

    By ttik, June 30, 2011
    • 2 replies
    • 1,767 views
    • 
    • ttik
    • July 3, 2011

19. alignment issues

    By Betterbait, February 27, 2010
    • 4 replies
    • 1,301 views
    • 
    • Betterbait
    • February 28, 2010

20. All cuts are shrunk

    By dlwheeler, February 26, 2011
    • 1 reply
    • 988 views
    • 
    • dlwheeler
    • February 26, 2011

21. All the help I can get

    By gohartman, February 26, 2008
    • 4 replies
    • 980 views
    • 
    • kenimes
    • February 27, 2008

22. Also...

    By gohartman, February 26, 2008
    • 8 replies
    • 1,113 views
    • 
    • kenimes
    • February 27, 2008

23. another request for pinch rollers (or help with slippage)

    By dwneumann, June 12, 2010
    • 3 replies
    • 1,494 views
    • 
    • Dakotagrafx
    • June 25, 2010

24. Another usb to serial adapter driver question?

    By Monkeywithumbs, February 12, 2009
    • 1 reply
    • 967 views
    • 
    • CyberChuck
    • February 14, 2009

25. Any experience with Vinyl express Cuttr

    By Betterbait, March 4, 2010
    • 12 replies
    • 12,093 views
    • 
    • stetson5331
    • May 21, 2011