Search the Community

I need some help on deciding what to get drop your opinion. I've done some research on titan 3 cutter and there's not much info out there or videos on how and what kind of cuts or quality it does? Does it get close to what a graphtec ce7000-60 plus do ?

Anyone know if the Titan 2 is compatible with SBE? and if so, which cutter should be selected? TIA

So about a month ago our computer crashed and we had to update and reinstall vinyl master on our new hard drive. I have been having issues with calibration. I called support and was told to possible change the carriage. A tech came out and changed the carriage however my laser arms and alignment are still cutting off my image. Is there not anyone in Dallas that knows this machine to help when your contour cut of an image is not cutting correctly? We have a hanging project until I can figure this out.

Hello - I'm wondering if anyone knows what the compatible blade is for the Titan 2 machine. My niece just got a machine (second hand), and I want to pick-up a couple of Clean Cut Blades for her, but am not sure which to select. TIA.

Hello, New to the US Cutter world. Had Mimaki's in the past. I purchased a used Titan 3 28" cutter from a friend. He was unable to find the manual and software PSN so I had to purchase new VinylMaster Cut v5. I haven't been able to get it to communicate with the cutter. The Titan machine does make a test cut from the keypad on the Titan, but nothing from the VinylMaster software. Called tech support and they walked me through troubleshooting steps and determined my I/O board is bad. In Device Managers, under Ports, the USB Serial (COM3) does show up. Is this a common problem? I ordered the I/O board from US Cutter. Any tricks to installing it? Thanks, Nick Signs by Nick Denver

Can the Titan 2 with a stand, be used as a tabletop cutter, without the stand?

I'm new to cutting vinyl. Just picked up the titan 3 a couple months ago and I'm finally getting around to trying it. I would like to cut some small logos for my shop. I'm thinking like 3" x 2.5" with lettering. Right now I'm using 45 degree cheaper Blades offered from the uscutter site. I'm using 631 vinyl. The small letters look alright but sometimes they pull up while I'm trying to weed. I did the test cut feature but it still seems to do it. Once I make the logo bigger it works better. What recommendations would you guys have? Thanks!

Hi, I'm new to the forum and these topics. I'm looking to make stencils, paint masks, etc for pinstriping and air brushing. Also Vinyl lettering and exploring more about cutters possibilities. Also looking at input for the software. Like graphtec studio pro vs vinylmaster dtr vs coreldraw? I'm looking for a relative simple software that's beginner friendly. I'm not looking to hand create anymore. Looking for suggestions and ideas to exploring this new adventure. Thank you

I purchased the HP Latex/Titan 3 Combo and want to perfcut decals. Looking for someone who might be doing this already to save me a couple steps.

This is the version that has ALL cutters listed, not just the cutters sold by USC. It is the trial version but fully functional. So far, I am not sdeeing the 'count down' but who knows. http://www.mediafire.com/?sharekey=7946f9ac31f5034cd9d5c56d04dfa8b0e04e75f6e8ebb871 feel free to DL...it will stay up for 60 days, but will continue to stay up as long as someone downloads it every 30 days. edit: For some reason teh file is no longer there. I am checking into it. Meanwhile, it can be had here: http://www.filesavr.com/sbewsetup

Hello, I have purchased a TITAN 3 for its wide cutting capability, but I have a big issue. We cut small vinyl (car stickers) in quite large quantities, several hundred per day. Until now, we were cutting these files on a Roland (using Versaworks), which has an automatic nesting and grouping function. However, now I'm considering transitioning to the new tool. I have subscribed to VinylMaster, but I don't know how I can import multiple files at once and then cut them simultaneously using the nesting function of the software. Since I am new to using the software, a step-by-step explanation would be very helpful, or if you can find one, a video showing how to do this would be greatly appreciated. Thank you very much!

So I just got the Titan II after previously owning the USC Laserpoint II. I already have Vinyl master installed on my PC but I'm having trouble connecting my new cutter. I was able to connect the device to Vinyl master via Auto detect after installing the drivers but I still cannot find my cutter on the "Current Cutter" options. See attachment. Do I need to reinstall vinyl master with the new product key even though I already have it??

I'm having trouble with SignBlazer seeing my fonts when I download them. ever since SignBlazer did an upgrade things seems to be much different. Any help would be greatly appreciated. I can see the font has gotten installed but not in SignBlazer.

i finally got my uscutter 630 w/ the signblazer s/w. figured out how to work it using text from the fonts provided. is there a way to use the text from the s/w and importing fonts from my windows font folder?

Bought a used non working Titan 3 68 inch from an individual. Powers up, green led on power supply, fan runs, display and buttons light up, but is blank. Replaced carriage board and gained that now when powered up it says us cutter and titan 3 in display then goes blank. Replaced motherboard and display is same but also now the carriage move to the right side now and that is it. The only button on the control panel that gets a reaction is the reset button, all others no response. Have replaced the carriage ribbon wire with new and same results. Have tried all combinations with both Carriage boards and both motherboards and both carriage ribbons with no change. I have a green led on solid and a red led flashing on the motherboard. I've been working with Greg and Steve from support but neither have been able to tell me what the flashing red LED means. They are in the process of trying to get me a new control panel but I have mine out and looks good. I asked for all new ribbon cables and a new i/o board but they thought the i/o board wasn't the problem. My ribbon cable on my display appears to me to be permanently attached but they say not. I've got cuts a lot pro 5 loaded om laptop with usb cable, no change, and laptop does not recognize cutter. Any suggestions. And thank you to support, they have made every effort to get this thing going but haven't come up with the correct answer. What am I missing here? Possibly a bad wire from power supply over to the right side. New motherboard could be bad? Has correct part number on packaging. There's not much else to go bad , is there? Right now I'm hoping it is the white ribbon cable going up to the display. The push button board looks perfect, can't see anything wrong there. The white cable on the display has a couple kinks in it but no bare spots. All connections were still siliconed except where the i/o board cable plugged into the motherboard. Thanks in advance.

Can anyone show me how to delete the registration from popping up everytime i load up signblazer

does anyone know where I can download an older version of signblazer. I have the program on a very old PC and dont have the install CD. I need to get the program and old files to my new computer :( any help would be appreciated

Ok I just got a titan 2 after owning a vinyl express a long time ago. Been out the game about 6 years. On my old machine I could load vinyl and hit enter and it would size my vinyl so I knew what size media I had to work with. Does the titan do this or am I missing something. So far I just load it and guess lol

Hello US Cutter friends! I'm in need of a bit of help with my new TITAN 15" cutter. I'm using cutter software of my own sourcing, as I need to command the cutter in a very simple but particular ways to accomplish my cuts (basically just giving the machine HPGL code), but in order to do so I need to know the COM, TCP/IP, and which PORT to use for my new TITAN 15" cutter. Can any of you help me? Thank you for any help you can provide. I'm happy to answer any questions you may have. Cheers, -FF

Hello… I am really struggling on something . I currently use a silhouette cameo and it literally runs all day and all night… I use it to cut stencils to make wood signs. The lettering are use can be big or a can go to a 1/4”. I have a mac and are you sure cuts a lot for all my designs. Money is tight… really tight. I understand the benefits of a servo motor....im desperately in need of a better machine than what I currently is… But again money is very tight. Can you all chime in on options for me… Even if I went with the original titan would I see some great improvement over what I currently use!?! Feeling so overwhelmed -big and important secision thank you cindi

I have only used this Titan 2 a couple of times and has been a year since last use. Recently I created a stencil and I tried to make an adjustment to rotate/ make the numbers larger. now the cutter blade is all the way down and cuts and pushes the stencil paper into a mess. Also the blade gets real hot. Can anyone advise. THX

Is there any way to turn off the sound effects that the Titan 3 has? Super distracting

Using two of the Titan-2 28” at my work and I have a Titan-3 SE 28” at home, all are using Vinylmaster DSR V4.0. Using the Titan-2 this past week I had a 30 piece 3-layer vinyl project and each layer of the design was about 20x20 inches. One thing that would have made this project a little easier if I could figure out how the “Advance After Plot” works. This is at the bottom of the attached photo. What I think this is supposed to do is advance to the cut trough so you can make the cut. Doesn’t appear to work checked or unchecked. I have been manually advancing the X position on the Titan-2 to 120 to make the cut and then back to 15 for the next plot. The Titan-3 has a different cut trough location. Have not found any setting in Vinylmaster or in the cutter itself for the “Advance After Plot” length. I hope this is not a repeat question as I have searched through the forum and did not find a solution. Any ideas would be appreciated. Thanks, Dave

Does anyone know or can they confirm if the Titan 1 control panel will work on the Titan 2 ? I pinched my display cable(s) while changing the mother board & belt. So only part of my display works as with only half the controls.. But UScutter doesn't have any in stock for the titan2.

I've downloaded the SignBlazer program, is there any way to use it without being in Trial Mode? Is there a 'one size fit's all' type Activation code? Or a different download that just gives the program w/o the extra options.