GraphTec Cutting Plotter Support Requests

368 topics in this forum

1. CE6000-60 FIrmware Update

   By eight2ten, May 11, 2013
   • 5 replies
   • 4,355 views
   • 
   • MZ SKEETER
   • May 12, 2013

2. Graphtec changing speed?

   • 1
   • 2

   By mfatty500, May 4, 2013
   • 29 replies
   • 6,588 views
   • 
   • MZ SKEETER
   • May 6, 2013

3. Completing cut

   By Twiz89, May 2, 2013
   • 6 replies
   • 1,295 views
   • 
   • Twiz89
   • May 2, 2013

4. Graphtec 2250 Table Surface Worn Out

   By plainblackguy, April 30, 2013
   • 0 replies
   • 845 views
   • 
   • plainblackguy
   • April 30, 2013

5. Graphtec ce6000-40

   By Ricktharula, April 27, 2013   

   • Trouble shoot
   • 2 replies
   • 2,079 views
   • 
   • Dakotagrafx
   • April 27, 2013

6. Graphtec FC8000 series - cuts choppy toward end of job

   By MidnightGlassworks, April 27, 2013
   • 24 replies
   • 3,909 views
   • 
   • Dakotagrafx
   • April 28, 2013

7. Qe60 cutter turns on but doesn't do anything

   • 1
   • 2
   • 3

   By prettybird, April 19, 2013
   • 58 replies
   • 11,999 views
   • 
   • sharon0johnny
   • December 17, 2018

8. Why is 651 white fighting me so much?

   By Coaster36, April 17, 2013
   • 10 replies
   • 2,337 views
   • 
   • dwp99
   • April 18, 2013

9. Graphtec CE5000 120 running SignBlazer

   By chefgary, March 21, 2013
   • 8 replies
   • 2,577 views
   • 
   • chefgary
   • November 26, 2013

10. Strange cut on CE6000-60

    • 1
    • 2

    By toddlamp, March 9, 2013
    • 25 replies
    • 11,519 views
    • 
    • MZ SKEETER
    • March 12, 2013

11. The tips of my A's are lifting, advice?

    • 1
    • 2

    By motoxchic, March 1, 2013
    • 30 replies
    • 4,289 views
    • 
    • motoxchic
    • March 7, 2013

12. CE6000, some awesomeness and some frustration

    By motoxchic, February 24, 2013
    • 0 replies
    • 877 views
    • 
    • motoxchic
    • February 24, 2013

13. Weird J with some cuts... CE6000-60

    • 1
    • 2

    By theishkid, January 24, 2013
    • 26 replies
    • 4,973 views
    • 
    • barakusa
    • December 8, 2014

14. New GraphTec CE-6000 40/60/120-amo Series

    By NichoDesign, January 7, 2013   

    • graphtec
    • graphtec 5000
    • (and 4 more)

      Tagged with:

      • graphtec
      • graphtec 5000
      • graphtec 6000
      • vinyl cutter
      • plotter
      • cutter
    • 3 replies
    • 4,524 views
    • 
    • NichoDesign
    • January 18, 2013

15. USED FC-5100 or NEW CE-5000?

    • 1
    • 2

    By theishkid, December 18, 2012
    • 28 replies
    • 7,664 views
    • 
    • Dakotagrafx
    • January 5, 2013

16. Graphtec ce5000 40cpr

    • 1
    • 2

    By Imlost21, November 13, 2012
    • 29 replies
    • 4,076 views
    • 
    • MZ SKEETER
    • November 14, 2012

17. Craft Robo to cut monogram

    By ahood, October 31, 2012
    • 2 replies
    • 1,550 views
    • 
    • edge
    • October 31, 2012

18. Graphtec FC7000-75 Poll Size not working OSX Lion

    By timnog, September 12, 2012   

    • graphtec
    • lion
    • (and 1 more)

      Tagged with:

      • graphtec
      • lion
      • osx
    • 0 replies
    • 3,106 views
    • 
    • timnog
    • September 12, 2012

19. Graphtec F2100-50

    By ggmoreira, September 12, 2012   

    • Overcut and Cutter Offset
    • 2 replies
    • 1,292 views
    • 
    • ggmoreira
    • September 12, 2012

20. Graphtec FC7000-MK2-130 -- Chatter

    By khpsi, July 16, 2012   

    • graphtec chatter
    • contour
    • 4 replies
    • 4,420 views
    • 
    • MZ SKEETER
    • July 16, 2012

21. Graphtec 5000-60 mark error cancel message

    By rharmon12, June 13, 2012   

    • mark error
    • 1 reply
    • 6,444 views
    • 
    • OWJones
    • June 13, 2012

22. How to get back home

    By Trumpy, June 8, 2012
    • 3 replies
    • 1,211 views
    • 
    • Jay2703
    • June 8, 2012

23. New Graphtec with Corel X3 and Cutting Master 2 - everything rotated 90 degrees from preview...

    By OWJones, June 5, 2012
    • 6 replies
    • 2,506 views
    • 
    • OWJones
    • June 5, 2012

24. contour cut and signmaster 2 cutting error?

    By han7681, May 27, 2012
    • 0 replies
    • 1,243 views
    • 
    • han7681
    • May 27, 2012

25. Graphtec in for warranty work

    By zamboy1, March 27, 2012
    • 5 replies
    • 1,669 views
    • 
    • MZ SKEETER
    • March 28, 2012