USCutter Refine Cutting Plotter Discussion

811 topics in this forum

1. MH871

   By hharley3059, April 9, 2010
   • 17 replies
   • 3,449 views
   • 
   • Team Satan
   • May 2, 2010

2. What speed and pressure do you run?

   By John Thomson, September 28, 2008
   • 9 replies
   • 3,395 views
   • 
   • firemalt
   • December 8, 2008

3. blade which way

   By stickyicky612, September 3, 2008
   • 6 replies
   • 3,339 views
   • 
   • dustinjtrr
   • September 6, 2008

4. mh871

   By kev09, February 5, 2010
   • 6 replies
   • 3,326 views
   • 
   • BannerJohn
   • February 5, 2010

5. Cutter stops in the middle of a cut - I don't think it is static.

   By lionsnwings, December 11, 2009
   • 8 replies
   • 3,297 views
   • 
   • CKR
   • December 15, 2009

6. Trying to Set up Mh-871 on laptop- cannot get computer to recognize the cutter!

   By rbeaman204, June 21, 2010
   • 4 replies
   • 3,270 views
   • 
   • CRD
   • June 25, 2010

7. Differences in the MH351, MH721, MH871 etc

   By muibubbles, January 31, 2012
   • 3 replies
   • 3,248 views
   • 
   • mom22boys
   • February 26, 2012

8. MH 721-MK2 Cutting Problems

   By bigrapidstrophies, October 9, 2012   

   • Not Responding
   • Never-ending Lines
   • 1 reply
   • 3,240 views
   • 
   • Jay2703
   • October 9, 2012

9. Grounding my plotter?!? Knife is dragging.

   By JoeCamaro, December 3, 2007
   • 11 replies
   • 3,178 views
   • 
   • Guest fivestar
   • December 5, 2007

10. Can not open the output device. Error initializing cutter

    By laserman70, January 10, 2008
    • 18 replies
    • 3,162 views
    • 
    • kenimes
    • January 14, 2008

11. Cutting a printed whatever...

    By gmatov, July 7, 2007
    • 18 replies
    • 3,150 views
    • 
    • Amey Design Sign Graphics
    • August 24, 2007

12. Serial Port to USB? Cutter wont finish a project! Wasted Vinyl

    By earlsembroidery, February 21, 2008
    • 17 replies
    • 3,144 views
    • 
    • cutme
    • March 17, 2008

13. How do you stop uncontrollable unrolling of vinyl material

    By George B, May 26, 2010
    • 10 replies
    • 3,143 views
    • 
    • prestonservco
    • May 28, 2010

14. MH-721 computer to cutter issue

    By muddywaterpirate, January 19, 2010
    • 21 replies
    • 3,100 views
    • 
    • muddywaterpirate
    • February 5, 2010

15. cutting strip replacement

    By tservice, July 16, 2011
    • 7 replies
    • 3,045 views
    • 
    • BannerJohn
    • July 23, 2011

16. MH721 Pinch roller settings

    By mabco12, May 5, 2010
    • 7 replies
    • 3,041 views
    • 
    • Guest HowardI
    • June 25, 2010

17. mh721 heat transfer paper

    By themaras, April 19, 2011
    • 8 replies
    • 3,024 views
    • 
    • Dakotagrafx
    • April 21, 2011

18. MH-871 setup in Sign Blazer

    By Rob Law, January 18, 2010
    • 5 replies
    • 3,014 views
    • 
    • Rob Law
    • January 20, 2010

19. MH721 - Cutting skewed/warped circles

    By Gav S, August 17, 2011
    • 11 replies
    • 3,010 views
    • 
    • Gav S
    • August 17, 2011

20. It is normal on my HM-871?

    By Carlosgraphic, July 17, 2011
    • 4 replies
    • 2,983 views
    • 
    • Rodger
    • July 18, 2011

21. Refine VS. PCUT ...

    • 1
    • 2

    By protek, June 1, 2008
    • 29 replies
    • 2,965 views
    • 
    • polarkiss
    • June 4, 2008

22. mh721

    By thredz, September 25, 2006
    • 0 replies
    • 2,962 views
    • 
    • thredz
    • September 25, 2006

23. Cutting Strip on MH721

    By xJoey Dubsx, October 12, 2010
    • 5 replies
    • 2,960 views
    • 
    • Fred Kaz
    • September 30, 2012

24. possible burnt out motor?

    • 1
    • 2

    By Matt.S, July 29, 2008
    • 35 replies
    • 2,948 views
    • 
    • kenimes
    • August 8, 2008

25. Loading Vinyl!

    By absolute_customs, April 12, 2010
    • 7 replies
    • 2,931 views
    • 
    • absolute_customs
    • April 13, 2010