TITAN 2 Series Vinyl Cutter Discussions

165 topics in this forum

1. Over Size Please Reset!

   By RRS1983, June 10, 2020
   • 2 replies
   • 1,509 views
   • 
   • MZ SKEETER
   • June 10, 2020

2. Vinyl Cutting Software Recommendations

   By matt12, May 4, 2020
   • 3 replies
   • 1,281 views
   • 
   • Wildgoose
   • May 5, 2020

3. Probably nitpicking here but...(Cutting finished vinyl from roll after design is cut)

   By Cliff P, May 1, 2020
   • 10 replies
   • 1,354 views
   • 
   • Cliff P
   • May 2, 2020

4. Cutting letter format (8.5x11") sheets on my 28" Titan 2

   By Cliff P, April 29, 2020
   • 3 replies
   • 1,051 views
   • 
   • MZ SKEETER
   • April 29, 2020

5. 45 degree blade offset

   By GHEENEE1, April 9, 2020
   • 4 replies
   • 1,748 views
   • 
   • haumana
   • April 9, 2020

6. Anyone know what overcut is?

   By mpanek, March 5, 2020
   • 10 replies
   • 2,095 views
   • 
   • Dakotagrafx
   • March 5, 2020

7. vectors

   By Strikenmike, February 14, 2020
   • 1 reply
   • 930 views
   • 
   • bikemike
   • February 14, 2020

8. Configuration conflict

   By Strikenmike, January 25, 2020
   • 9 replies
   • 1,331 views
   • 
   • haumana
   • January 26, 2020

9. Titan2 leftmost pinch roller not in sync?

   By handmadelovely, December 27, 2019
   • 3 replies
   • 994 views
   • 
   • slice&dice
   • December 28, 2019

10. Titan2 Issues

    By Eazy, December 1, 2019
    • 8 replies
    • 1,191 views
    • 
    • Eazy
    • December 3, 2019

11. titan 2 cutting issues

    By Daveischosen, November 5, 2019   

    • titan2
    • cutting issues
    • 7 replies
    • 1,851 views
    • 
    • Wildgoose
    • November 8, 2019

12. Titan 2 not cutting correctly

    • 1
    • 2

    By jamiefeld, October 9, 2019
    • 34 replies
    • 4,741 views
    • 
    • Caseman315
    • December 22, 2019

13. Downloads/drivers

    By Caseman315, October 9, 2019
    • 6 replies
    • 3,535 views
    • 
    • Wildgoose
    • January 10, 2023

14. Titan 2 cuts super slow on a specific design

    By marquezjc, September 27, 2019
    • 11 replies
    • 977 views
    • 
    • slice&dice
    • September 27, 2019

15. Mimaki CJ 150 prints to cut on Titan ll

    By Johnmpcny, September 12, 2019
    • 8 replies
    • 1,154 views
    • 
    • Dakotagrafx
    • September 13, 2019

16. Help with VM Ltr

    By bigmax, August 4, 2019
    • 2 replies
    • 767 views
    • 
    • Wildgoose
    • August 4, 2019

17. Blade holder will not raise up

    By ryugaiden05, August 3, 2019
    • 6 replies
    • 875 views
    • 
    • ryugaiden05
    • August 8, 2019

18. Cut strip

    By GHEENEE1, June 29, 2019
    • 4 replies
    • 906 views
    • 
    • Dakotagrafx
    • June 29, 2019

19. Mr Thompson

    By vernil thompson, June 22, 2019
    • 2 replies
    • 849 views
    • 
    • Dakotagrafx
    • June 22, 2019

20. Help!! Magnet cutting, machine hard to calibrate

    • 1
    • 2
    • 3
    • 4
    • 7

    By Kristof, June 15, 2019
    • 157 replies
    • 9,571 views
    • 
    • Buggie Pilot
    • August 6, 2019

21. Upgrade Question

    By rdunn12, March 12, 2019
    • 7 replies
    • 1,165 views
    • 
    • darcshadow
    • March 12, 2019

22. Titan 2 mother board install

    By Scotts Games, February 27, 2019
    • 6 replies
    • 1,257 views
    • 
    • haumana
    • February 27, 2019

23. Cutting machine not found

    By 1916Gear, February 23, 2019
    • 10 replies
    • 1,198 views
    • 
    • haumana
    • February 23, 2019

24. Not feeding straight

    By George Wever, February 17, 2019
    • 4 replies
    • 1,696 views
    • 
    • haumana
    • February 18, 2019

25. Both of my Titan 2's randomly stop cutting

    By skulldaddy, January 4, 2019
    • 2 replies
    • 1,414 views
    • 
    • MZ SKEETER
    • January 4, 2019