GraphTec Cutting Plotter Discussion

484 topics in this forum

1. Recommended Blades for CE6000-60

   By wickedstangs, February 29, 2016   

   • Blades
   • 9 replies
   • 2,508 views
   • 
   • Jburns
   • May 20, 2016

2. How can I stop my Graphtec cutter from lifting on every line segment?

   • 1
   • 2

   By bigmark1972, February 23, 2016
   • 28 replies
   • 3,592 views
   • 
   • Wildgoose
   • February 25, 2016

3. CE 6000-60 vs the Titan 3 28 inch.

   By RedTacoDriver, January 29, 2016
   • 4 replies
   • 2,296 views
   • 
   • Primal Decals
   • August 6, 2016

4. Graphtec CE5000-60 Weed frame alignment issues

   By kimmy123, January 23, 2016
   • 0 replies
   • 937 views
   • 
   • kimmy123
   • January 23, 2016

5. Graphtec help needed

   By xpaperman, December 10, 2015
   • 19 replies
   • 2,515 views
   • 
   • jaybyrd
   • February 18, 2016

6. FC8600 not cutting small stuff properly

   • 1
   • 2

   By TimEdwards888, December 9, 2015
   • 40 replies
   • 7,457 views
   • 
   • TimEdwards888
   • December 15, 2015

7. Thinking about buying from Alibaba - do fakes exist?

   By Trillion, December 7, 2015
   • 11 replies
   • 1,684 views
   • 
   • Trillion
   • December 11, 2015

8. Best plotter cutter for absolute detail work? (less than 5mm characters)

   By Jonesy, November 26, 2015
   • 17 replies
   • 5,040 views
   • 
   • Jonesy
   • November 27, 2015

9. CE6000-60

   By Signs and Designs, November 14, 2015
   • 3 replies
   • 1,117 views
   • 
   • Dakotagrafx
   • November 14, 2015

10. Graphtec JX1130 SignJet Pro 54

    By MadHatterGraphix, October 23, 2015
    • 8 replies
    • 3,173 views
    • 
    • MadHatterGraphix
    • October 24, 2015

11. How to stop my CE600-60 from lifting the blade in corners?

    By bigmark1972, October 21, 2015
    • 3 replies
    • 1,542 views
    • 
    • Jeremy76
    • April 14, 2018

12. Graphtec fc4100-130 cutting project from vinyl spool

    By jcsocal, October 14, 2015
    • 5 replies
    • 1,575 views
    • 
    • jcsocal
    • October 14, 2015

13. What Maintenance to do CE5000

    By Izzy11, October 10, 2015
    • 11 replies
    • 3,569 views
    • 
    • Dakotagrafx
    • October 14, 2015

14. Contour Cutting with my Ce5000

    By gcextreme, October 9, 2015
    • 14 replies
    • 1,846 views
    • 
    • MadHatterGraphix
    • October 27, 2015

15. Opensource designsoftware with Graphtec CE6000-60

    By Dylantje, October 1, 2015   

    • Opensource
    • 9 replies
    • 2,458 views
    • 
    • Dakotagrafx
    • October 2, 2015

16. Graphtec

    By jdmarti1, September 30, 2015
    • 11 replies
    • 1,700 views
    • 
    • djque
    • October 4, 2015

17. CE6000-60 Newbie issues, Curves & Cut Controller

    • 1
    • 2

    By terranomade, September 27, 2015
    • 35 replies
    • 15,128 views
    • 
    • MZ SKEETER
    • November 27, 2017

18. Craft Robo Pro losing its bearings and shooting off the end of A3

    By heleno, September 16, 2015
    • 2 replies
    • 789 views
    • 
    • heleno
    • September 17, 2015

19. CE-5000 syncing

    By Richcg, September 1, 2015
    • 2 replies
    • 2,370 views
    • 
    • Richcg
    • September 1, 2015

20. Graphtec CE6000-60 problems

    • 1
    • 2

    By MadHatterGraphix, August 7, 2015
    • 26 replies
    • 9,404 views
    • 
    • MadHatterGraphix
    • August 7, 2015

21. Graphtec Craft Robo Pro issues

    • 1
    • 2

    By top53, July 21, 2015
    • 31 replies
    • 5,310 views
    • 
    • decalfarm
    • August 7, 2020

22. Graphtec FC3100 and Cutting Master 3 on iMAC CS6 Adobe Suite

    By timshaw64, July 14, 2015
    • 3 replies
    • 865 views
    • 
    • timshaw64
    • July 16, 2015

23. Ce 6000 cutting width

    By Cosmic1, July 1, 2015
    • 2 replies
    • 1,850 views
    • 
    • Cosmic1
    • July 7, 2015

24. Graphtec 6000 motherboard change

    By Appleuser, June 25, 2015
    • 9 replies
    • 2,152 views
    • 
    • SMW
    • March 23, 2016

25. CE6000-120 Graphtec STudio Help Needed

    By bizzytop, June 21, 2015
    • 3 replies
    • 921 views
    • 
    • bizzytop
    • June 22, 2015