GraphTec Cutting Plotter Discussion

General discussion pertaining to the GraphTec cutting plotters. (Please do not post support requests here)

484 topics in this forum

  1. stencil material slides out of place

    By Spotted Dog,
    • 1 reply
    • 529 views

  2. Removal of pinch roller

    By Anetski,
    • 12 replies
    • 2,073 views

  3. Graphtec 8600 Cutting Jagged Lost Settings

    By Capt'n Morgan,
    • 0 replies
    • 464 views

  4. Graphtec CE6000-40 Sensor Offset Adj

    By LouLouNovice,
    • 0 replies
    • 566 views

  5. Having a Scale issue !

    By Josh mason,   
    • 3 replies
    • 922 views

  6. Settings seem off

    By 3 Kells Design,
    • 10 replies
    • 1,146 views

  7. Cutting out off line

    By Dee's T's & More,   
    • 1 reply
    • 538 views

  8. Plotter Controller

    By Pradeep,
    • 1 reply
    • 579 views

  9. New-to-me Graphtec CE6000-40 Plus

    By Rojhan,
    • 1 reply
    • 799 views

  10. GRAPHTEC CE6000-60 NOT WORKING

    By JOSE GARCIA,
    • 2 replies
    • 1,451 views

  11. CE6000-40 adding random cut lines

    By AbsoluteInk,
    • 1 reply
    • 513 views

  12. Graphtec ce6000-60 vinyl rollers

    By Grandpa,
    • 7 replies
    • 887 views

  13. Ce6000-60 Plus RANDOM Extra Cut Lines or diagonal scribbles all over job

    By New Creations By Jen,   
    • 23 replies
    • 1,754 views

  14. Brand new CE7000-60 starts, cuts a 1cm line then moves 2cm and starts to cut job

    By Kembs,
    • 9 replies
    • 836 views

  15. Cutmaster 4 job setup question..

    By keith20mm,
    • 0 replies
    • 567 views

  16. CE6000-60 Not Reading Registration Marks

    By MerchForFans,
    • 1 reply
    • 1,074 views

  17. FC8000 Y belt maintenance?

    By EverythingVinyl,
    • 0 replies
    • 587 views

  18. Graphtec FC9000 Cutter Issue (May not be be issue with the cutter)

    By Ddecals,
    • 1 reply
    • 671 views

  19. Software update

    By bikemike,
    • 9 replies
    • 909 views

  20. CE5000-40 Unable to access menu

    By Can,
    • 6 replies
    • 1,001 views

  21. Its Been A Long Time Question Please

    By Capt'n Morgan,
    • 3 replies
    • 694 views

  22. Graphtec ce7000 not finishing cuts.

    By Nellycuttz,
    • 13 replies
    • 1,678 views

  23. Firmware graphtec ce 5000

    By jhon,
    • 3 replies
    • 758 views

  24. Knife drags a cut from origin to the starting point of the artwork?

    By iamclaus,
    • 17 replies
    • 2,239 views

  25. Graphtec CE5000-60 Scans Media and Stops

    By DCWT954,
    • 4 replies
    • 1,054 views