Copam Cutting Plotter Discussion

217 topics in this forum

1. Keeping Vinyl Tracking

   By Mobile, May 14, 2008
   • 11 replies
   • 17,682 views
   • 
   • allceasons
   • September 21, 2009

2. Copam 3050 not cutting straight lines, question not answered.

   • 1
   • 2

   By Fatboy, April 19, 2014
   • 42 replies
   • 7,240 views
   • 
   • smokey13
   • September 25, 2014

3. importance of vinyl used versus blade for detail cutting

   • 1
   • 2

   By JSPEK, December 2, 2009
   • 32 replies
   • 7,667 views
   • 
   • Sandstormdesigns
   • December 16, 2009

4. Advantages of the Copam 2500 over the LP24?

   • 1
   • 2

   By MecH, January 30, 2009
   • 28 replies
   • 4,396 views
   • 
   • Benr98
   • February 1, 2009

5. bad cuts at an angle

   • 1
   • 2

   By omgpandasaurus, March 21, 2011
   • 27 replies
   • 6,158 views
   • 
   • omgpandasaurus
   • April 26, 2011

6. has anyone got the copam to contour cut manually?

   • 1
   • 2

   By abullock22, April 26, 2010
   • 26 replies
   • 4,650 views
   • 
   • MZ SKEETER
   • May 19, 2010

7. Copam just delivered

   • 1
   • 2

   By Uncle Remus, February 11, 2009
   • 25 replies
   • 4,382 views
   • 
   • Opsid-Design
   • April 17, 2009

8. Has Anyone went from a MH series to a Copam? Real world differences?decision

   By wayne1234, July 9, 2010
   • 22 replies
   • 4,941 views
   • 
   • Dakotagrafx
   • August 3, 2010

9. New copam question....

   By DanielB, January 18, 2009
   • 20 replies
   • 2,329 views
   • 
   • Benr98
   • January 18, 2009

10. Review of Copam

    By kst8catfan, October 29, 2009
    • 19 replies
    • 8,606 views
    • 
    • Dakotagrafx
    • March 13, 2012

11. Copam 3050 Uneven cut pressure

    By Fatboy, July 2, 2014
    • 19 replies
    • 3,681 views
    • 
    • Fatboy
    • September 8, 2014

12. cp-2500 windows 7

    By brian08, October 15, 2009
    • 18 replies
    • 7,538 views
    • 
    • joshlw
    • July 15, 2010

13. COPAM DRIVER "THE REAL THING"

    By Jason50, August 18, 2007
    • 17 replies
    • 6,694 views
    • 
    • PixelPusher
    • January 6, 2016

14. how old is your copam 2500

    By designed, April 26, 2009
    • 16 replies
    • 3,555 views
    • 
    • Sew Darn Hot
    • August 5, 2009

15. Question about copam accesories.

    By racinboy30, July 26, 2009
    • 16 replies
    • 2,319 views
    • 
    • MZ SKEETER
    • July 26, 2009

16. Which would you buy?

    By lonestarcountrymusic, April 23, 2010
    • 16 replies
    • 1,765 views
    • 
    • lonestarcountrymusic
    • April 24, 2010

17. Pinch Rollers

    By Guest Finishing Touch, July 5, 2012
    • 16 replies
    • 3,609 views
    • 
    • Guest Finishing Touch
    • July 20, 2012

18. Copam CP-2500 Setup Problems

    By williamssignco, March 5, 2010
    • 15 replies
    • 7,173 views
    • 
    • MZ SKEETER
    • August 7, 2010

19. Can the Copam cut offline side to side?

    By Kittycut, August 5, 2009
    • 14 replies
    • 3,308 views
    • 
    • longarm
    • November 12, 2009

20. not cutting anything with a perfect corner all letters have a little blip

    By bcxprint, September 7, 2011
    • 14 replies
    • 2,933 views
    • 
    • MZ SKEETER
    • September 7, 2011

21. Copam Ballpont Pen Holder + Pen

    By CyberSultan, April 16, 2008
    • 13 replies
    • 1,804 views
    • 
    • CyberSultan
    • May 7, 2008

22. Could this be causing YOUR tracking problems?

    By pitts-s1s-pilot, October 10, 2008
    • 12 replies
    • 1,967 views
    • 
    • Rodger
    • October 15, 2008

23. Blade & Pressure

    By three47b, June 25, 2010
    • 12 replies
    • 2,537 views
    • 
    • YadirellT
    • July 8, 2010

24. Vinyl Lifting issue

    By omgpandasaurus, March 16, 2011
    • 12 replies
    • 11,478 views
    • 
    • FrogDog
    • February 1, 2015

25. Malfunctioning Co Pam

    By mongo, April 16, 2011
    • 12 replies
    • 2,813 views
    • 
    • AshComputers
    • April 16, 2011