Creation PCUT Cutting Plotter Support Requests

740 topics in this forum

1. How to replace power supply on ct-630

   By inksane, April 10, 2012
   • 3 replies
   • 1,841 views
   • 
   • perry 13654
   • April 27, 2012

2. Cut pressure

   By Dayveboy, April 8, 2012   

   • Pcut 630
   • 0 replies
   • 1,815 views
   • 
   • Dayveboy
   • April 8, 2012

3. Need help with the MH series

   By greenistheway, April 7, 2012
   • 5 replies
   • 1,472 views
   • 
   • MZ SKEETER
   • April 7, 2012

4. Cutter completing about a quater of a design and then stopping "waiting"

   By koletsb, April 4, 2012
   • 2 replies
   • 1,290 views
   • 
   • koletsb
   • April 5, 2012

5. pcut 1200e not cutting precisely

   By mrrask, March 31, 2012
   • 7 replies
   • 1,934 views
   • 
   • mb20music
   • April 1, 2012

6. PCUT 1200 Slices through image, & "Waiting" HELP!!!! PLZ!

   By rtrevino821, December 17, 2011
   • 13 replies
   • 3,161 views
   • 
   • rtrevino821
   • March 11, 2012

7. Creation Pcut Cutter loads firmware over and over?

   By xstar, March 11, 2012
   • 0 replies
   • 1,311 views
   • 
   • xstar
   • March 11, 2012

8. Blade Chatter

   By dhuff125, March 9, 2012
   • 1 reply
   • 1,471 views
   • 
   • mb20music
   • March 9, 2012

9. Blades for Pcut 630

   By THier, February 27, 2012
   • 0 replies
   • 1,352 views
   • 
   • THier
   • February 27, 2012

10. New Laptop,, P-cut won't inititionize

    By THier, February 19, 2012
    • 17 replies
    • 3,432 views
    • 
    • BearlyRich
    • February 22, 2012

11. pcut/flexi stopping just before end of design

    By adcentre, February 9, 2012
    • 10 replies
    • 4,083 views
    • 
    • adcentre
    • February 9, 2012

12. Please help, Creation CT630 cutting in reverse

    By cgg09, April 8, 2010
    • 9 replies
    • 3,514 views
    • 
    • MZ SKEETER
    • February 9, 2012

13. cuting with windows 7 ?

    By MR kranwinkel, June 12, 2011
    • 5 replies
    • 2,220 views
    • 
    • MZ SKEETER
    • February 9, 2012

14. Yes, you can cut directly from Corel (12, x3, x4 and x5)

    By BearlyRich, February 8, 2012
    • 0 replies
    • 6,434 views
    • 
    • BearlyRich
    • February 8, 2012

15. Cutter not 'finishing off' cuts properly. (on going issue)

    By Azonic, February 7, 2012
    • 2 replies
    • 1,855 views
    • 
    • mb20music
    • February 7, 2012

16. Creation PCut CR630 not finishing cuts (Static issue?)...

    By HarveyLester, January 24, 2012   

    • creation pcut cr630
    • static
    • (and 2 more)

      Tagged with:

      • creation pcut cr630
      • static
      • ground
      • not finishing cut
    • 3 replies
    • 3,302 views
    • 
    • MZ SKEETER
    • January 25, 2012

17. CT360 USB issue / Signblazer

    By stagdriver, January 24, 2012   

    • USB
    • Signblazer
    • 0 replies
    • 2,926 views
    • 
    • stagdriver
    • January 24, 2012

18. Random Straight cuts

    By jmatson, January 8, 2012
    • 0 replies
    • 1,073 views
    • 
    • jmatson
    • January 8, 2012

19. PCUT froze & screen blank

    By Luvmydane, January 4, 2012
    • 3 replies
    • 1,439 views
    • 
    • MZ SKEETER
    • January 4, 2012

20. cuttin image bigger than it should

    By benjaming, December 9, 2011
    • 6 replies
    • 1,498 views
    • 
    • MZ SKEETER
    • December 11, 2011

21. Creation Kingcut A280..... Need help BAD !!!

    By lobsterman22, October 17, 2011
    • 1 reply
    • 2,607 views
    • 
    • kenimes
    • November 8, 2011

22. line is not connected to the point it starts

    By ttik, August 9, 2011
    • 16 replies
    • 3,848 views
    • 
    • ttik
    • November 8, 2011

23. memory maybe?

    By livinloudgraphics, September 7, 2011
    • 6 replies
    • 1,960 views
    • 
    • MZ SKEETER
    • October 7, 2011

24. Buying a new Motherboard

    By wotz101, September 22, 2011
    • 0 replies
    • 1,359 views
    • 
    • wotz101
    • September 22, 2011

25. Creation P-CUT CR630 with SignBlazer?

    By shavlik, September 20, 2011
    • 0 replies
    • 1,488 views
    • 
    • shavlik
    • September 20, 2011