Search the Community

Hello everybody! Recently bought a Vevor KI-720A to do small things around the house, just a hobby! The software that came with it is SignMaster 3.x and the few times I used it it worked correctly, but I took advantage of the discount and updated it to the CUT V5 Basic Edit version, everything is working with the exception of the following: During the contour cutting process, when I'm going to align the 4 points, if for some reason I click on the arrow to move the head to the right, it moves to the left and if I don't reset or turn off the head it keeps crashing at the end until I turn it off or do a reset (There is no limit switch on both sides). The impression I have is that when I press the button to the right, the SignMaster sends a negative number and I put the head in ZERO and it moves to the opposite side as if it were to take a turn. Has anyone had a similar problem? Do you have any tips to solve this problem? Thank you all!

Did you follow the instructions that we gave you on your first thread in Feb? Make sure you find the FTDI driver (online) for your computer operating system, download and install, and run, Reboot computer. Go into your computer device manager, find the com port number 1-4 nothing higher. Then choose the same com port number in Signmaster. The com port numbers must match or the computer will never communicate with the cutter. USB is not TRUE USB in value cutters, like higher end cutters. I have not read anything good about Vevor. You can put Vevor in the search box upper right and choose everything.

I found a machine at the trusty pawn shop the other day and couldn't resist. It doesn't appear to be used at all, still has the protective films on it. I've tried using it under VEVOR KI-720 in the one software that actually lists that model in the menu but no luck. The USB jack was bent a little but my computer sees a USB device in device manager that corresponds to the machine in question. I've downloaded and installed most of the popular cut programs under demo mode and it appears the softwares are so limited I can't find any cutter models in the setup menus at all except the Sure Cuts A Lot demo that doesn't work. The machine doesn't look antiquated at all but although generic it appears modern. I'm not sure the machine is even a VEVOR brand, there's only the model number on it. I see the same KI-720 model number on Alibaba and a couple of other obscure China websites that provide no apparent support.

Vinyl master has that cutter listed Vinylmaster.com Make sure you find the FTDI driver (online) for your computer operating system, download and install, and run, Reboot computer. Go into your computer device manager, find the com port number 1-4 nothing higher. Then choose the same com port number in Vinylmaster. USB is not TRUE USB in value cutters, like higher end cutters. I have not read anything good about Vevor. You can put Vevor in the search box upper right and choose everything.

Yes, I see it is a Vevor brand.(after searching model number) People come here and claim it is a night mare machine. Just put Vevor in the upper right search box. (search everything) Plenty comes up.

yeah i think I'm starting to see the issue, ive just googled KI-870A and it comes up with a VEVOR machine that looks exactly like this one, and looking at images of the MH721 on US Cutter website there's a subtle difference like sticker location and the LCD panel is blue where mines white... i may have been had over as i know VEVOR machines dont work with Flexisign (so ive read) i have a small work around, i draw and design in flexi, export and then import into sign master and it cut perfectly

It appears your vinyl cutter is a Vevor. so contact their support. I have only seen people on here screaming that their Vevor cutter is a nightmare, support@vevor.com

is there any software out there compatible with a vevor VV375 cutter. artcut came with it and i cant even use the images that came with disk. also the image tracing is sub par. the machine cuts well just cant find anything that will play with it..HElp!

Is Vevor still in business? Their website is Copyright 2015 showing 2017 NEW arrivals. This is what searches of Vevor bring up. http://www.vevor.com/vevor-business-industry-home-kitchen-health-beauty-automobiles/cutting-plotter.html http://www.vevor.com/cutting-plotter-53.html

Hi, It's me; John! From Netherlands. I'm not a professional signmaker, just a hobbyist, I wouldn't even call myself a signmaker. About me: Born in 1976, occupation: welder/mechanic. I have had a Roland CX-24, with flexisign 7.5 pro software, working with a Compaq laptop running Windows XP since 2007. Purchased to make our own decals for our pulling tractor. Fast forward to 2021....Because I couldn't get it to work with a new PC with windows 10 and no serial port, I have sold the complete Roland setup for €500,- and bought a new cutter for €250,-. The new cutter is a Vevor KI-720 A. It came with Signmaster software and USB connection cable. It looks very similar to MH cutters, and my guess is that they might be fabricated at the same company or at least in the same country. Anyway; while searching for any info about these cutters I came across this forum, so here I am. I also purchased a cheap heat press recently for €80,-. The Vevor cutter is working perfectly, now. I did have some problems, but solved them. Some problems have been fixed because I found the same issues that people were having with their MH cutter here on this site. I will make some new posts about the problems, issues, spare parts and breakage I have had already, as it might help someone. Groeten en houdoe! (it's Dutch...)

I have a K1-1350 and it came with SignMaster Cut, basic cutting software. It came with signmaster on a thumbdrive - which could not be used to install the software. Had to use the optical drive to install.It's decent budget cutter, but so far has been working flawlessly. If you can find a copy of SignMaster Cut, it comes with the drivers and all that is needed. Of course since I am answering you two years too late, if you haven't gotten it working then you likely have tossed it. I bought mine new from vevor.com for around $500. Mine has a comm port, which your model unfortunately does not have - and the comm port is easiest way to set up. If you use the USB port, then you need the driver. https://signmaster.software/cut-tools-features/

TROUBLE STRUCK: HELP NEEDED Hi Everyone I am facing the issue of black vinyl peeling off in the adjoining picture. It has been happening only with the black vinyl, rest of the colors are fine. This has been happening after a few days of the first wear. I have applied Heat transfer vinyl (other colors of vinyl on to the colored fabric) sometimes using household iron and sometimes using heat press but have never experienced this before. Here are the details: HTV Brand: BFlex Preheat temperature: 150 deg celcius Pressing time: 15-20 seconds Shirt material: Pure Cotton (Brand Anko available at Kmart) Heat press used: Vevor I tried pressing the vinyl again using heat press but on one or two shirts it started to peel off again after I test washed it. I am giving it a normal wash with maximum temperature of 80 degree celcius (in accordance with the data sheet of the vinyl). I had a word with someone else in the company and was told that the white fabrics and garments are coated with some sort of stain resistant coating so they don't get stained while passing through many hands. This may interfere with the sticking of the vinyl. What am I doing wrong guys?

let us know how that works out for you - if she has an order that big waiting in the wings order a titan and have a big portion paid off on the first order. In another post you asked if the vevor was comparable with the lp3 - being no one on here has used a vevor nor most of us heard of it I think that will be hard for someone to determine but how often does a plotter that cost 1/2 as much be comparable to the higher end machine. maybe the answer is at the vevor forum and support web site

Yep, I stand corrected, but still, I like that VEVOR with the pre-spaced rollers. Anyway it's all Chinese knock-offs of the Rolands and Graphtecs. Vevor or not to Vevor? THAT is the question!!!

I have the SignMaster Pro software and a Vevor KI-870 cutter. For some reason the software is not recognizing the cutter any more. It worked for over a month. Then one day it has stopped. I tried updating the driver. I tried the steps that SignMaster have sent me. The sent me a Chip Driver software but for some reason my computer is not downloading it. I keep getting that error. Can someone please help. I am a school teacher. I really need help figuring this out before I go spend money that I really don't have on a Circut.

It looks like a chinese imitation of a vevor branded cutter

I wonder if the O-P was trying to just get his unidentified machine to run, or was seeking info on the functions? The settings (red button) would not be pressed in general, no need for it in regular operations. "Leave" is essentially "Offline" ---- to adjust the x & y axis movement with the arrow/directionsl keys and place the vinyl and carriage head in position (then hit "Origin" to set). I would run up the speed to max (up arrow) which is likely 800. ---- I never reduce speed from max, let 'er rip! The force is dependent on the media/vinyl, and if the blade is properly adjusted, a test cut will determine what exactly to adjust this value at (90 might be a better starting point). By the way, it's a VEVOR branded unit.

John, Thanks for coming along and making these posts. Anecdote: I have a friend who intended to buy a USCUTTER machine to do a specific project she had to quickly complete, but at the time, the 34" unit she wanted was out of stock, and she liked the look of the Vevor machine (870) and figured what the heck -- and went with that. I helped her set it up, showed her how to run the software, and provided tutorials on signmaking techniques. What turns a hobbyist into a 'professional signmaker' -- money!

This is a user to user forum. UScutter rarely comes here. Contact Vevor.. UScutter sells parts for a Refine and a Liyu vinyl cutter. Look and see if there is a part number on it and then search online for the part number. We would not have any idea if they are compatible.

If you check VEVOR in the searches. people are coming here with problems. http://forum.uscutter.com/index.php?/search/&q=vevor

Just a friendly piece of advice for everyone who is contemplating purchasing a USED cutter -- Always have the seller provide a demonstration of it working with the computer connected, and then, ask for that computer to be included with the sale! Otherwise, what you may be purchasing is just an expensive brick. I had a friend of mine purchase a Vevor machine, it would NOT run correctly with SignBlazer, no matter what. The unit came with a version of SignMaster that had the correct driver. You may wish to contact them to ask if your model is supported. https://signmastercut.com

I bought a Vevor 1350 and didn't come the drive. Where can i find the drive to install?

I have the Vevor 1350 and you can use Easycutstudio downloaded from the internet. Make sure you select the right port under cutter settings for it to communicate with the computer.

Why not contact Vevor? They should have the measurements for their machines and parts, Your supplier is your tech support.

Hmm- I thought they were similar MH Head VEVOR Head VEVOR pinch rollers MH Pinch Rollers VEVOR Cutter MH Cutter