-
Content Count
658 -
Joined
-
Last visited
-
Days Won
4
Content Type
Profiles
Forums
Gallery
Everything posted by tooler82
-
I would assume it wouldn't be any different. I've always used the RTape 4075RLA. It's excellent transfer tape.
-
I don't know how good it is, but I ordered some RTape Prograde Paint Mask that's yellow. Don't know what temp it goes up to, only says it can withstand short term bake cycles at +200 degrees Fahrenheit
-
USB TO PRINTER CORD
tooler82 replied to BNS16's topic in LaserPoint Cutting Plotter Support Requests
When we bought our printer and Grimco came and set it up, the installer said anything over a 6 ft cord will have data loss. It sucks because I need a long one for my setup at the shop, but had to rearrange to get the printer close to the computer. -
I've never understood how people make money on twitch. What's your channel?
-
Have the 3M. Also if you have to go on rivets be sure to use some Pro Bond or some other kind of adhesive promotor / primer.
-
I hope I was able to help them.
-
3M A7322 or Orajet 3967AC
-
Here's Chapter 8 with all the info. ama_Ch08.pdf
-
On fixed-wing aircraft, marks must be displayed on either the vertical tail surfaces or the sides of the fuselage. If displayed on the vertical tail surfaces, they shall be horizontal on both surfaces of a single vertical tail or on the outer surfaces of a multivertical tail. If displayed on the fuselage surfaces, then horizontally on both sides of the fuselage between the trailing edge of the wing and the leading edge of the horizontal stabilizer. Exceptions to the location and size requirement for certain aircraft can be found in 14 CFR part 45. On rotorcraft, marks must be displayed horizontally on both surfaces of the cabin, fuselage, boom, or tail. On airships, balloons, powered parachutes, and weight-shift control aircraft, display marks as required by 14 CFR part 45. Almost universally for U.S.-registered, standard certificated, fixed-wing aircraft, the marks must be at least12 inches high. A glider may display marks at least 3 inches high. In all cases, the marks must be of equal height, two-thirds as wide as they are high, and the characters must be formed by solid lines one-sixth as wide as they are high. The letters “M” and “W” may be as wide as they are high. The spacing between each character may not be less than onefourth of the character width. The marks required by 14 CFR part 45 for fixed-wing aircraft must have the same height, width, thickness, and spacing on both sides of the aircraft. The marks must be painted or, if decalcomanias (decals), be affixed in a permanent manner. Other exceptions to the size and location of the marks are applicable to aircraft with Special Airworthiness certificates and those penetrating ADIZ and DEWIZ airspace. The current 14 CFR part 45 should be consulted for a complete copy of the rules.
-
Tried all the sites I know, but can't find this font.
-
They didn't cut them for me. I ended up using the band saw and it didn't do so well.
-
Lol! I'll try. They're always trying to save a $. I order 12" and 24" RTape. What did I get? Yeah they changed the order to 2 rolls of 48" and told me to cut it to however big I need it to be because that's cheaper than buying different sizes.
-
Hate to bother you again, but realized there's a different font on the graphic they want too. Do you know this one?
-
I did a little google search and found this: http://www.ideas-r-us-software.uk/FileConverters/SilhouetteStudioConverter.aspx
-
Most Clear transfer tape for making vinyl stickers
tooler82 replied to Powerboss's topic in General discussion
For clear I use RTape AT-65, but it's a high tack so not sure how good that'll be doing layered vinyl. My stuff is print. -
It's weird my print has been fine for years. All of a sudden it's junk. Was told it's the profile, but of course nobody has a profile out there for 3M IJ35C for Flexi. Just a rant.
-
I'm building it based on that suggestion from the other forum. It'll take some time, but hey it's a government job so I have time lol. I think I need to get them to order some Oracle to try instead of this IJ35C we've used forever. Thanks.
-
Thanks a lot. I was actually on that post on signs101 reading it when you posted. I'm going to try to tweak it like he did and see. Yeah the icc profile sites you sent are what I've been checking every week, but they never put one out. Thanks.
-
Being Army we don't get to do these often, but they look good. I'm usually stuck doing the usual retirement plaques on our laser. We have an Epilog Zing 24 30 Watt.
-
ps4 Playstation 4 (PS4) Decal Vector - Consol & Control
tooler82 replied to Mayo's topic in Graphic Requests
If you did a search I've put the PS4 controller on here. I'm attaching it and the PS4 though as I have made this one a template. The last light bar I put up was my personal one. Hope it helps. PS4 Light Bar Updated.eps PS4 Template.eps- 3 replies
-
- 3
-
- playstation
- control
- (and 5 more)
-
What doesn't kill you only makes you stronger. Except an A-10 that'll kill you. It's amazing it was about to be taken out of service until Iraq and Afghanistan and then they figured it's the ultimate plane for that kind of fight. Delivering freedom at 3,900 rounds per minute. Love those bad boys.
-
What's the best way to figure out a replacement ICC Profile for your printer, material, and rip software? Just download a bunch and keep trying them out? They don't have one for the material we use, and it's always been ok until we spent over $3,000 getting the printer fixed. New head, capping station, etc and now it's off. The color isn't too bad, but it dumps so much black out and it's like fuzzy on the edges. Just don't understand why they don't have ICC Profiles for every 3M product. I don't understand. I figured that would be a requirement.
-
Thank you skarekrow. I'll show you guys the engraving when I get it done. It should be pretty funny.
-
This government computer blocks access to everything! There's a guy retiring and they want me to engrave a credit card customized to this guy's retirement stuff, but can't download it. Thanks. http://www.google.com/url?sa=i&rct=j&q=&esrc=s&source=images&cd=&cad=rja&uact=8&ved=0ahUKEwjjptH7opbOAhUF4CYKHaOuDCMQjB0IBg&url=http%3A%2F%2Fwww.vector-eps.com%2Fcredit-card-vector%2F&psig=AFQjCNFYIVI_CF38c_bljfe-iUmdUHDylg&ust=1469798573846751
-
This one