blacklabelgraphix 3 Posted March 24, 2016 I just went to Cutterpros.com support and installed the driver there it installed just fine....They sell Sagas. And they have Flexi install instructions. Where did you find the driver on that site? Share this post Link to post Share on other sites
MZ SKEETER 4,709 Posted March 24, 2016 Ok that worked, run as administrator...On UScutter.driver....It installed. But I did not have to do that at CutterPros.com 1 Share this post Link to post Share on other sites
blacklabelgraphix 3 Posted March 24, 2016 carolyn - did you try right clicking on the setup file and select run as administrator? When I right click on the setup file it doesn't give me that option. Share this post Link to post Share on other sites
Dakotagrafx 7,297 Posted March 24, 2016 Ok that worked, run as administrator...On UScutter.driver....It installed. But I did not have to do that at CutterPros.com Thanks for verifying Share this post Link to post Share on other sites
MZ SKEETER 4,709 Posted March 24, 2016 When I right click on the setup file it doesn't give me that option. Right click the Set up.,,, go down to properties. Then security tab, Then choose admin... Share this post Link to post Share on other sites
blacklabelgraphix 3 Posted March 24, 2016 Ok I got the driver to install. I think. Still does't cut. Or do I need to restart computer first? Share this post Link to post Share on other sites
MZ SKEETER 4,709 Posted March 24, 2016 Yes, it would be best to reboot and start fresh, Your cutter should recognize it, when plugged in. 1 Share this post Link to post Share on other sites
blacklabelgraphix 3 Posted March 24, 2016 Ok. I rebooted. When I go to cut, production manager says "Cutting...0%" for a while then says "Write port error." Share this post Link to post Share on other sites
Dakotagrafx 7,297 Posted March 24, 2016 Ok. I rebooted. When I go to cut, production manager says "Cutting...0%" for a while then says "Write port error." what port is shown on the active cutter in production manager? Share this post Link to post Share on other sites
MZ SKEETER 4,709 Posted March 24, 2016 Reassign it a new comport number like Com 3, Then match Com 3 in Flexi.set up. and see if that works Share this post Link to post Share on other sites
Dakotagrafx 7,297 Posted March 24, 2016 I would make that usb since we just installed the usb drivers and with the titan usb works fine - Share this post Link to post Share on other sites
MZ SKEETER 4,709 Posted March 24, 2016 Go into Flexi ,,,set up add cutter,, and Choose the 135011 (that should be Titan 2 53 inch.) and choose USB. 1 Share this post Link to post Share on other sites
blacklabelgraphix 3 Posted March 24, 2016 Go into Flexi ,,,set up add cutter,, and Choose the 135011 (that should be Titan 2 53 inch.) and see if USB is there. Yes I have that cutter set up in production manager. I plugged into a different usb. It comes up com9. I changed that in the setup too. Share this post Link to post Share on other sites
Dakotagrafx 7,297 Posted March 24, 2016 Go into Flexi ,,,set up add cutter,, and Choose the 135011 (that should be Titan 2 53 inch.) and see if USB is there. I think I read where he added the titan info to flexi so it might show up there - the wierd thing is when I had the 28" titan2 the driver was like the 720I and not the 720II that you would have thought Share this post Link to post Share on other sites
MZ SKEETER 4,709 Posted March 24, 2016 Yes I have that cutter set up in production manager. Ok... should work.. Share this post Link to post Share on other sites
Dakotagrafx 7,297 Posted March 24, 2016 Yes I have that cutter set up in production manager. I plugged into a different usb. It comes up com9. I changed that in the setup too. strange - my graphtec says usb - and I thought when I had the titan it said usb when properly configured but I don't have it anymore so can't confirm Share this post Link to post Share on other sites
MZ SKEETER 4,709 Posted March 24, 2016 Go look under UScutter, In Flexi..., and see it it might show up there, That is where the other cutters show up...AS USCUTTER...Or try Titan. Share this post Link to post Share on other sites
blacklabelgraphix 3 Posted March 24, 2016 Wow!. I don't know what I've done but it cuts now. In Control Panel/Devices and Printers I have: TITAN-1350I - USCutter TITAN 48 under "Printer and Faxes". Also I have: SAGA Cutter Plotter under "Unspecified". When I unplug the usb the SAGA Cutter Plotter goes away and pops back up when I plug back in. So what is the TITAN-1350I - USCutter TITAN 48 under "Printer and Faxes"? Share this post Link to post Share on other sites
MZ SKEETER 4,709 Posted March 24, 2016 If you followed the instructions correctly after installing the Flexi driver pack and copied it to your Flexi, Production Suite OUTPUT drivers it should read USCUTTER,listed in manufacturers according to the instructions of the READ ME file. . 1 Share this post Link to post Share on other sites
Dakotagrafx 7,297 Posted March 24, 2016 if it cuts now -don't mess - just use it - 1 Share this post Link to post Share on other sites
blacklabelgraphix 3 Posted March 24, 2016 Thank you guys for helping me with this!!! I really appreciate it a lot!!! I have another question about Flexi if you don't mind. Share this post Link to post Share on other sites
MZ SKEETER 4,709 Posted March 24, 2016 What version of Flexi?.. "Flexi" is the brand name, but there are several different versions starting with Flexistarter clear up to FlexisignPro....So what version? Share this post Link to post Share on other sites
blacklabelgraphix 3 Posted March 24, 2016 FlexiSTARTER 10 The cut contour icon is not lit up to be able to click on it. Share this post Link to post Share on other sites
MZ SKEETER 4,709 Posted March 24, 2016 I don't use Flexi 10, but you must have the item on your workspace selected, Then go to Effects. Contour. I use Flexistarter8.6 Share this post Link to post Share on other sites