prototype66 20 Posted February 2, 2011 I have an Ultra GRC76s, new 45 and 60 blades, offset on .025 (i read most people recommend .25 but mine goes by .0xx up to .060) down force ok....just enough too leave an impression in the backing slightly and speed set to 40-45 ips. cutting Universal Products 2 ml Auburn Metallic film. or 3M controltac film both As it cuts (smaller letters up to 1/2 to 3/4 an inch) it lifts the vinyl up as it cuts...and catches some on the blade sometimes too. I have played with different down force settings and offset but cant get it right. Any idea what I am doing wrong??? Share this post Link to post Share on other sites
Dakotagrafx 7,297 Posted February 2, 2011 less blade Share this post Link to post Share on other sites
lueman 19 Posted February 2, 2011 Less blade & drop some oil in the holder make sure it's clean. Share this post Link to post Share on other sites
Neuromax 97 Posted February 2, 2011 Yep, less blade. It took me a while to figure that one out too. Share this post Link to post Share on other sites
prototype66 20 Posted February 2, 2011 Ill get some 3-1 oil on the way home tonight I hadn't thought of that. As far as the blade ...it is about 1 to 2 mm out now so I was worried about the holder catching the lifted vinyl. Ill back it off some more. I read about the thickness of a credit card or less (usually 1/2 the thickness of the card edge) Thanks folks. Share this post Link to post Share on other sites
Dakotagrafx 7,297 Posted February 2, 2011 lot less than 1/2 the thickness of credit card - you should barely even see the blade. the credit card thing is too much blade . . . but it lives on Share this post Link to post Share on other sites
prototype66 20 Posted February 2, 2011 so only visible with my glasses! lol thanks Dakota and everyone else! Ill report back with the results. Share this post Link to post Share on other sites
prototype66 20 Posted February 2, 2011 **update** Backed off blade and oiled carrage....check TURNED TANGIBLE OFF!.....check set to fine cut.....check speed set to 25ips( now its actually going that fast!) ....check offset to .015.....check 3M controltac sucks.....double check other vinyl cut great but I think the blade is still too far out. so far so good on trial and error! Share this post Link to post Share on other sites
bayotle 26 Posted February 2, 2011 As a rule (for me) the blade is less than 1/2 the thickness of a credit card. Check that and see if it helps any.... Share this post Link to post Share on other sites
prototype66 20 Posted February 2, 2011 ill check it right now.....love the new photo! Share this post Link to post Share on other sites
bayotle 26 Posted February 2, 2011 y ty, just took it myself (Good luck! ) Share this post Link to post Share on other sites
Neuromax 97 Posted February 2, 2011 run your finger over the blade, you should BARELY feel it. It should be almost not visible. I kept trying to get it by the credit card trick but it always lifted. Once I just did it by feel it has worked great. Share this post Link to post Share on other sites
prototype66 20 Posted February 3, 2011 that seemed to help a lot ! I think its cutting properly now. I just need a higher quality vinyl like the copper color stuff. That 3M 170 controltac just wont cut nice for some reason. Share this post Link to post Share on other sites
bayotle 26 Posted February 3, 2011 I have a lighted magnifying glass i use which makes it a lot easier on us older folks Share this post Link to post Share on other sites
Dakotagrafx 7,297 Posted February 3, 2011 I have a lighted magnifying glass i use which makes it a lot easier on us older folks +1 and a wife with good eyes Share this post Link to post Share on other sites
prototype66 20 Posted February 3, 2011 that seemed to improve it but the 3M is still lifting. The copper color is great now. I just need top slow it down a bit and increase the down force. Share this post Link to post Share on other sites
bayotle 26 Posted February 3, 2011 I have a lighted magnifying glass i use which makes it a lot easier on us older folks +1 and a wife with good eyes You keep the wife, i'll keep my sanity! As far as it still pulling, that's about the extent of my experitise, I'll hafta refer you to the 4um experts! Share this post Link to post Share on other sites