SandyM114 0 Posted September 18, 2009 Would someone look at this pic and tell me if the carriage wheels are aligned wrong? My carriage black box looks like it's slanted backward toward the track and the wheels are on the outside of the groove. Someone mentioned his wheels are inside the track and I noticed mine look wrong. The cutter has been really noisy the past couple of days, so I might have something wrong. Thanks for looking. Share this post Link to post Share on other sites
Dakotagrafx 7,297 Posted September 18, 2009 looks like they are out of the track to me Share this post Link to post Share on other sites
SandyM114 0 Posted September 18, 2009 So the wheels should be inside the track or groove? How do I move them? Share this post Link to post Share on other sites
BannerJohn 1,324 Posted September 18, 2009 push the carriage UP and in until they snap into place. Share this post Link to post Share on other sites
SandyM114 0 Posted September 18, 2009 JOHN, WILL YOU MARRY ME? THANK YOU! Share this post Link to post Share on other sites
SandyM114 0 Posted September 18, 2009 It's fixed! Thanks John! I didn't realize it was off track until the other guy showed a pic of his carriage. I had noticed it sounded really bad, but the cuts were great, go figure...Sandy Share this post Link to post Share on other sites
VendettaVinyl 0 Posted September 18, 2009 That was issue #1 I have having with my refine. Share this post Link to post Share on other sites
BannerJohn 1,324 Posted September 18, 2009 JOHN, WILL YOU MARRY ME? THANK YOU! do you already have your own car? Share this post Link to post Share on other sites
SandyM114 0 Posted September 19, 2009 Yep! Got my own car.lol Thanks again! Share this post Link to post Share on other sites
Guest kenya Posted September 19, 2009 Hey John..... does that mean if Sandy has a car, we are ALL invited to a wedding? Share this post Link to post Share on other sites
BannerJohn 1,324 Posted September 19, 2009 always looking for #5. Share this post Link to post Share on other sites
Guest kenya Posted September 19, 2009 John 5 ?? You sound like my husband. He said that he was going to keep trying until he got it right...... he finally did. Share this post Link to post Share on other sites
SandyM114 0 Posted September 19, 2009 Uhhh. car just broke down.... darn.lol 5?? Share this post Link to post Share on other sites
BannerJohn 1,324 Posted September 19, 2009 If at first you don't succeed,etc... Share this post Link to post Share on other sites
Mike Roark 0 Posted January 21, 2020 Thanks for the input. Still having issues. I have checked and the cutter is on track. I tried to cut again and the cutter remained at the same spot, approximately 1/4 inch from the vinyl. I can slide the cutter up and down, but it will not do it on its own. Any and all suggestions are appreciated. I tried to call tech support, but..... they close at 4pm PST and I did not call until 7:05 PM Eastern time. UGH! Might be relying big time on this message board. Thanks, Mike Share this post Link to post Share on other sites
MZ SKEETER 4,709 Posted January 21, 2020 Go back to your original post, instead of posting to a thread from 2009. Share this post Link to post Share on other sites
Mike Roark 0 Posted January 21, 2020 those pictures are not of my blade holder, but no it does not go up and down when cutting. It goes left to right but nothing up and down. Share this post Link to post Share on other sites
Dakotagrafx 7,297 Posted January 21, 2020 Like skeeter indicated posting n two area of the forum does not improve your chances of getting help, especially when everyone is following your other post Share this post Link to post Share on other sites