corel 2017

[corel 2017]

Thanks mfatty I will give this a try. Thanks again, Mark

[corel 2017]

Cannot get contour or border to cut inside of letters. I can set contour around font but not the center such as on R or O. Thanks, Mark

[Vinylmaster LTR size]

Thanks for all the help. Mark

[Vinylmaster LTR size]

Thanks again for all your help. Mark

[Vinylmaster LTR size]

Thanks MZ SKEETER I gave it try, I set the size of test box to cut a 2"x2" square at 100% it cut a box 8"x8" . I reduced the percent to 25% and it did cut 2x2 square. My device units per inch is set at 1016 should I reduce this to 254? Thanks, Mark

[Vinylmaster LTR size]

My image is cutting about 4 times the size of original image. I am not sure how to calibrate size. Is there a factory setting that is standard in the device units per inch. Mine was set to 1600 units per inch.Thanks, Mark

[Vinylmaster LTR]

THANKS. MZ SKEETERK. Mark

[Vinylmaster LTR]

I upgraded to vinylmaster ltr , for the life of me I cannot figure out to access extra fonts. I did download the extras file. Thanks, Mark

[mossy oak]

Try tree silhouettes

[Arial font]

Thank you very much for your help, I really appreciate it. Thanks again, Mark

[Arial font]

Could someone help me with a default font, I choose a font , click on my page and the font reverts to arial 24pt. Any help will be appreciated . Thanks, Mark

[E-mailing cdr file]

Thank you both very much I really appreciate your help. Thanks again, Mark

[E-mailing cdr file]

probably should know this, what file type to use when e-maiingl a CDR file to someone without Corel draw. Just want include in body of e-mail. Don't know how to convert to jpeg. Can I send Bitmap and at what resolution? Thanks, Mark

[Graphtec ce 5000 / Cutting Master 3]

Thanks Mz Skeeter, sorry it took so long to say thank you for your help, Mark

[Graphtec ce 5000 / Cutting Master 3]

Thanks Mz. SKEETER,  the job is cutting fine, I thought the cut would begin at the origin point, bottom right if I sat that as the origin point and feed as it cut, I guess things are OK. Thanks again, Mark

[Graphtec ce 5000 / Cutting Master 3]

My last few jobs are cutting from the rear of design to front, I hope I can explain this right. I am cutting a design that is 35" I set the origin to begin cutting at the lower right hand corner, but the vinyl feeds the length of job and begins to cut pulling the vinyl back through. I am using Cutting Master 3. Thanks, Mark

[chevron pattern]

Thank you very much,sorry so late. Mark

[chevron pattern]

Could someone explain to me how to create a chevron pattern in Corel x6. Thanks, Mark

[help with this]

Be careful a lot of artwork is copyrighted. My Vinyl Designer has a collection of interchangable stick figures for a very reasonable price. Mark

[eliminating cross lines]

Thanks for all the help. Mark

[eliminating cross lines]

Could someone explain how to eliminate the cross lines where the guns intersect, so it looks as though one is in front of the other, can't seem to figure it out . Thanks, Mark

[Need a bass clarinet]

What is the difference between bass clarinet and a regular clarinet. I have a vector clarinet in my mega collection. Mark

[un-wanted cut line]

I am using Corel x-5, when I sent simple text to sign cut, in the preview it shows cut line going thru my text, cannot figure out to get rid of them. Thanks, Mark

[Problem with tool bar]

I can not change size of an object, or rotation of an object by typing the values in the tool bar, for size I have to go to arrange ,transformation, size. I don't know if I did something wrong in my settings? X-5. Thanks, Mark

[check mark in a box]

Thanks

Mike I will check it out. Mark