Bfutura15

I just started having an issue with my node edit. Now when go to node edit I have no outline to see what I am changing. It only shows the nodes. Anyone know? Maybe I changed a setting without knowing it.

That was it....Thanks

I went to install the pich roller and noticed that the other is also broke. So ordering another. So close yet so far away. I was hoping to install and test today. oh well.

Just ordered a new one. Crossing my fingers

I have noticed that one of my pinch rollers are cracked by the wheel. Could this have something to do with it?

What would you say pressure needs to be for Oracal 631?

Still didn't work. the blade was sticking out a little to far, but it did not fix it. tried messing with the X,Y, for another hour with no difference. it did not matter what I changed it to.

I will try these suggestions tonight and see what happens. Maybe my blade is sticking out to far. Thanks

Well the offset and reinstalling SB did not work. What is a good starting point for the X,Y? I have messed around so much with that I do not even know where factory is now.

I did not get to cut anything last night, but I know its not the roller. I am using 24" vinyl and the rollers are at the ends of the roll. I did make that mistake once before on a small sheet.

I sure will give that a try tonight. I have a few things that I need to cut. I will keep you informed. If I reinstall SB will I lose all the file I have saved?

Currently it is .35. I have tried 0-.50 in .05 incriments. Software is SB. The cutter is a LP24 w/ USB.

I have, it did not fix it either. This is what it is doing.

Did you ever get this problem fixed? I have had this issue for more than a year now and can never get an answer of the problem. I have tried everything suggested with no luck. X/Y, New Blades, New Holder, and offset. I worked on this one night for the better part of 3 hrs and wasted a lot of vinyl trying to fix it. Mine never does it with the pen.

I did and I did. Through the ebay store. Basically what is being told on here is what support and I were discussing. I have tried everything they suggested as well. Its got to be something that we are just missing, or should I say I am missing.

I keep getting a pigtail on my cuts and cannot fix it. The pigtail seems o be where the cutter starts the cut. I have tried everything so far no luck. I have adjusted the offset from 0-50, tighted the belt, read and adjusted the XY calibration from front to back, new blade, and new holder. Any suggestions? I will try to post a pic later.

A crease on the backing paper? That means too much pressure. With proper pressure and blade depth, you should just barely be cutting through the vinyl without marring the substrate. I will try to lighten the pressure and see what that does. Well my starting pressure was @ 110. I went down to 100 still did it. Again down to 95 still did it. At 95 It did not cut all the way through the vinyl.

A crease on the backing paper? That means too much pressure. With proper pressure and blade depth, you should just barely be cutting through the vinyl without marring the substrate. I will try to lighten the pressure and see what that does.

I have, no change

I keep having the same problem on my LP24. Nobody seems to have an answer. I will be replacing mine as well.

I can see what you are saying but the blade is barely sticking out. Only the tip is shown. The pressure has to be good since it cuts through the vinyl and leaves a light sign of where the graphic was. A crease if you understand what I mean. The next thing I am going to try is 60* blades. I am using what came with it and I cut small stuff. We are talking .80" and below. We will see what that does. However on the things that I do cut 1" and above it still does it with the 45*. Its just frustrating sometimes. It gets hard to weed the stuff.

Just for clarification - With a pen it will plot flawlessly, but with blade it will do what you pictured? Is it just text typed directly into SBE, or is it a graphic? If it is a graphic, post the file so others can take a look and see if there's something funky with the graphic itself. If it's a font, then let us know what font it is - not all fonts will cut nicely. Check the pressure that you're using. Make sure that the blade itself is clean, the surface of the blade holder is clean and that the cutting carriage moves up and down freely. I have pretty much given up. Yes, the pen is fine. No issue at all. This does it on everything. Graphics from Brand of the world, typed text, all. It doesnt matter. My pressure is normally always at 110. All items are clean and move freely. I at the point that I am saving up to purchase a better machine. This is getting on my nerves.

I normally only cut at 20,30,40 because of the size I cut at. This item was cut at 30. I gut something .52 tall x 1.90 wide at .10 last night and did the same thing.

I tried to get a picture but you cannot see the blade. Only the tip is seen. I even tried to adjusting it a little more in so less shows, but still does the same. Makes sense but it cannot be the case

But it happens on the test cuts that have nothing to do with SB.