-
Content Count
16 -
Joined
-
Last visited
Posts posted by HAMMERFALL
-
-
Ok my LaserPoint LCD display stoped working i turned it off then on and it worked, now its not going on at all. help!!!!!!!!
-
Hi. Im putting a third pinch roller on my laser point. but no instructions came with the roller on how to put it in.. how do i it? thanks
-
If the design isn't that wide , small rolls of vinyl can be used . I buy 3 1/2" ( & larger ) X 50 yard rolls from Stickerman5000 on e-bay at great prices plus cheap combined shipping . You can also cut down larger rolls to whatever size is best for tracking .
Ok thanks for the info. it never drifts the same way . sometimes left sometimes right. i just got the 3 rd pinch roller in today. now i need to find out how to install it. anyone know how to do this?? lol
-
Thanks for the info, i ordered the 3rd pinch roller. and am desinging some guid rails. from all i have read dont see that anyone tried that yet. so im gona give it a shot. we'll see :-The strangest one I have heard was a friend that actually helped there tracking using less blade.
That's what I did. Les blade and less pressure = less drag on the material, which helps to stop the material from shifting when making long cuts down one side of the vinyl. Anyway you slice it though, making a long cut down one side will usually cause some shifting. In over 10 years of doing this, I've seen just about every friction fed machine do it. If you do a lot of striping work, it pays in the long run to buy a pin fed machine. If you don't believe it, cut a long stripe down one side the with the vinyl aligned in the same spot, cut the same stripe down the center of the vinyl and compare. Take it one step further and cut the same stripe down the other side. You'll notice the vinyl always drifts away from the side being cut. That's because the drag from the blade is like a brake on that side. Placing two of the pinch rollers in the area being cut helps...Like this...
^
-------------------------------------------------
O O O
When I make long narrow cuts, I use the narrowest material I can get a way with and I cut down the center. The little bit of wasted vinyl is WAY cheaper than cutting the bob over and over trying to get it right.
Of course, you also have to align the vinyl dead nuts in order to track dead nuts. Even the best plotter will not track unless the vinyl is aligned properly. Don't rely on the front and rear rulers. Even the Roland I used to have was off by almost 1/8" on the rulers. My Refine is off by about 1/16". Make some test cuts and note where the material was on the rules before each cut. If it's dead on, you got lucky. If not, make a note align accordingly. Remember, what happens when you dry feed and what happens when there is a blade creating drag is not always the same.
-
I always prefeed.Don't make the plotter pull the vinyl off the roll - always prefeed the amount needed before starting the cut
-
Thanks for the info. i always run the vinyl through to set it up but it still drifts no matter what i do. ;(You can get an additional pinch roller on the USCUTTER homepage under Cutters, Parts. I think their 15$ for the laserpoint plus shipping.
Not sure that would help 100% though.
Make sure your rolls of vinyl are as tightly wound as possible and are trapped on both sides to prevent drifting side to side while being unrolled. Also some have luck unrolling enough material for the job into the material basket if you have one and run a test feed.
-
Hi , im having a issue with the vinyl drifting on long cuts with my laser point 24. im doing 6 ft cuts and its drifting about 1/8 to 1/4 a inch im doing pinstriping so this is a big deal. any help would be great, thanks btw theirs only 2 rollers that cant be adjusted as far as i know. thinking a 3 rd would help, if so where do i get it for this unit? thanks
-
some great info here, thanks all
-
Guess i missed that boat, the link is dead :thumbsup:
That post is from 2008 ??
Details details. lmao
-
-
Who offers the mylar? does it come on a roll or sheets?
they come as both, i found them on on ebay. And my US cutter laser point as well
-
ill give it a shot , thankswww.inkscape.org
-
try signblazer - it's free from usc
I have that, thanks. i need something i can do my artwork in and vectorize it in. sorry i should have been more clear on what im looking for.
-
Interesting thread.
-
Hi, everyone. I'm new to this and am looking for some ez to use softwhere i can work with. any advise?
i do my art work in photo shop 7. and need to convert it to vector base.
LCD SCREEN VERY HARD TO READ >>>>>FIXED!!!<<<<<<
in LaserPoint Cutting Plotter Support Requests
Posted
Sweet my lcd just died. gues now would be the best time to do that since im their. lol thanks for the post