-
Content Count
85 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Everything posted by CodyMcAllister
-
I haven't seen much on here for screen printing and haven't seen much equipment on USCutter pertaining to screen printing. Anyone got a favorite site to use for equipment and supplies? Press will DEFINITELY come from USCutter though. Can't beat their service. lol.
-
What degree blade for Oracal 351 Polyester chrome?
CodyMcAllister replied to CodyMcAllister's topic in Vinyl
Sounds like a plan dude. Thanks! -
I've got a car to do with this vinyl/polyester but not sure which blade to put in my new blade holder? I bought a new holder to use instead of readjusting my "regular" vinyl holder. Any idea or tips? Blade depth, speed, pressure? Thanks guys!
-
What type of chrome did you use?
-
Setting the home position; I think?
CodyMcAllister posted a topic in Copam Cutting Plotter Support Requests
When the machine starts a cut the blade will go from the left side of the machne all the way to the right and feed about 2 feet of vinyl before it starts the cut, "wasting" 2 feet of material before the vinyl image is made. I've read about a home position or origin; is this what I need to set, and how do i set it? -
Setting the home position; I think?
CodyMcAllister replied to CodyMcAllister's topic in Copam Cutting Plotter Support Requests
10-4 Guys and gals, I want to thank all of you for the help. This Copam machine is going strong and cutting long with VERY few to NO mistakes. Lol. Thanks for all your help! -
Setting the home position; I think?
CodyMcAllister replied to CodyMcAllister's topic in Copam Cutting Plotter Support Requests
Wow, the pressure was set on 90. Got it on speed 30, Pressure 20, and offset of .25mm. -
Setting the home position; I think?
CodyMcAllister replied to CodyMcAllister's topic in Copam Cutting Plotter Support Requests
Pressure is set at default. Haven't even messed with it yet. I've got it cutting better but the edges are still a little jagged. Tiny pieces are left over at the points of most letters. How do I adjust the pressure and what are the recommended settings? -
From the album: Trouble...
Any ideas on my problem? -
From the album: Trouble...
Any ideas on my problem? -
-
-
Setting the home position; I think?
CodyMcAllister replied to CodyMcAllister's topic in Copam Cutting Plotter Support Requests
Brand new blade and strip. The blade doesn't seem to be cutting into the backing paper so I'll start with the blade rotating. Thanks -
Setting the home position; I think?
CodyMcAllister replied to CodyMcAllister's topic in Copam Cutting Plotter Support Requests
Any help is greatly appreciated. The weeding took place MUCh easier than last night after I reset the blade depth and made the font a little thinker, but the decals are still looking pretty rough... -
Setting the home position; I think?
CodyMcAllister replied to CodyMcAllister's topic in Copam Cutting Plotter Support Requests
What settings should I start out with for 651 Oracal Intermediate vinyl. Pressure, offset, and so-forth? Thanks guys for helping too. I was rather dis-heartened last night when i first started with this "beast." lol -
Setting the home position; I think?
CodyMcAllister replied to CodyMcAllister's topic in Copam Cutting Plotter Support Requests
Having trouble setting the blade depth. I used the "sticky note" method to where the blade would cut through a single sheet and not the second one, but I still had irregular cuts where tiny pieces were left on some smaller letters. Have been using scrap vinyl for about an hour now cutting circles like USCutter recomends with the blade holder in-hand and I have it to where I can cut a circle with no jagged edges and BaRelY a mark in the backing paper. We'll see how it goes... -
Setting the home position; I think?
CodyMcAllister replied to CodyMcAllister's topic in Copam Cutting Plotter Support Requests
Seems like the machine cuts the vinyl as it is laid out on my workspace. I.E. if the decal to be cut is in the top left of the workspace, the machine cuts it on the far left and in about a foot on the vinyl. Place the decal in the bottom rigthhand of the workspace, and it cuts it from the right side of the vinyl and at the place where the blade rests. -
Setting the home position; I think?
CodyMcAllister replied to CodyMcAllister's topic in Copam Cutting Plotter Support Requests
SCALPro and Inkscape -
Lots of questions to ask and loads of help needed...
CodyMcAllister posted a topic in Pre-sale questions
We are looking to start a SMALL vinyl business. I own a few racecars, and my wife's family has numerous racecars also. We will be lettering our own cars and also doing many friends cars and cars as a business. We are looking at the Copam plotter as it is recoomended for production use. Would a economy model plotter hold up to this work or would the Copam be better? Also, we are basically oblivious as to what software to get. Do we upgrade to the best CorelDraw or go ahead and get Flexi? I'm not exactly a computer genius, but I'm handy with them and can learn ANYTHING with a little practice. ALso, what size plotter would be best? I've noticed that the prices are a little higher for vinyl over 24" or so. And I'm guessing you can change the orientation of an object in order to make it larger if it needs to be bigger than 24 if you have a 24" plotter. ANY help is appreciated. Thanks! Cody -
Lots of questions to ask and loads of help needed...
CodyMcAllister replied to CodyMcAllister's topic in Pre-sale questions
Inkscape has been downloaded and I'm pretty handy with it by now. Any other suggestions for software? Free preferably for now... -
Lots of questions to ask and loads of help needed...
CodyMcAllister replied to CodyMcAllister's topic in Pre-sale questions
Copam machine has been ordered!!!!!!!! Thanks guys! -
Lots of questions to ask and loads of help needed...
CodyMcAllister replied to CodyMcAllister's topic in Pre-sale questions
Thanks -
Lots of questions to ask and loads of help needed...
CodyMcAllister replied to CodyMcAllister's topic in Pre-sale questions
15' should be plenty! Thanks. Will the Copam cut regestration marks or is that an option in the sign programs? -
Lots of questions to ask and loads of help needed...
CodyMcAllister replied to CodyMcAllister's topic in Pre-sale questions
Really considering the Graphtec now as it was mentioned and recomended by a few people earlier. How bad would the tracking be on the Copam? Does anyone know?