-
Content Count
1,038 -
Joined
-
Last visited
-
Days Won
74
Posts posted by bikemike
-
-
I would say just get the condition settings for the condition you are using. May not matter since you have to set it up again for that blade problem.
You may not have a choice but to do the factory reset. That should not be heading right like that. And not that fast.
-
Maybe even take a can of that computer cleaner (canned air? forget the name of it) and go over the full width dusting every hole, rollers and anything else you can get to. Q-tips work good for the sensor holes.
-
-
Make sure you get that blade in before you fix the blade holder. Something will get damaged if you don't.
For the Y position. Try moving the vinyl and left pinch roller over to the center of the blue stripe.
Also, take some masking tape sticky side up (maybe 6 to 8 inches long) and put it under the pinch rollers on the smooth part of the roller, with the machine off, and slowly pull the tape out. That should help get some of that gunk off the rollers. May have to do it a few times.
-
Probably nothing to do with it, but it looks like you have 1/4 inch of blade sticking out?
And your blade holder is in wrong. That lip should be under the clamp.
- 1
-
Make whatever you do want to cut a different color, then cut by color.
- 3
-
Also a bit of oil may help. I put a small drop on a small piece of scrap vinyl and dip the end (opposite the cutting end) in that before putting it back together.
- 3
-
+1 on the bleed. I always add the bleed to make sure there is no white showing.
- 3
-
If you can get it clean enough, yes. Remove and replace. Watch for fading on the plastic.
- 1
-
1 minute ago, Tony chamu said:It doesn’t say much about vinyl
I don't think I have head of anyone on here that has the AP version.
-
I will give you that one. The AP does say for paper and such.
Didn't read the full specs, stopped at the pattern part.
-
The part that has the cuts in it IS the cutting strip. All one piece.
Not sure what you mean by narrow and wider.
-
What vinyl are you using?
-
4 minutes ago, Dakotagrafx said:unloaded - downhill with a tailwind - 9-10 with 5th wheel
Yup, where I am at. 402ci (6.6 liter) turbo diesel.
-
Lucky you only got that with a MH.
The trim would be right after install. Pretty simple actually. Free hand it and pull the excess. Have done it on painted drywall with no problems.
-
On 12/23/2019 at 9:18 PM, Dakotagrafx said:Ohh she wanted the srt but I wanted one vehicle that got more than the 14mpg my truck gets for going on vacations and if we buy something down south for the winters. it has a sound system that would have made me proud in my teens I think the same engine as the journey but with the 8 speed trans and newer software if smokes the Journey RT. for someone that is currently looking the employee pricing is hard to pass up and the reason we decided on now and to store it till june 1st when she retires - then sell the Journey
You get 14 MPG????
I am lucky if I can get 9 with my truck. (10,000 trailer, but still)
- 1
-
Depends on the cutter. Some do not track as well as others. What are you using for a cutter?
When I had that problem I used a sharp blade and trimmed the intersections so they lined up.
Just note, you need to install the bottom first to keep rain and such from getting behind the seams.
-
How deep do you plan to blast?
That stuff would probably be good for up to and inch deep or more in brick.
There is thinner stuff that would more than likely to do what you need.
-
You can use a USB to serial adapter. Keyspan is the recommended one.
-
Since it is not text, just move the 9 to the right and draw a rectangle the size you want.
- 2
-
5 minutes ago, Dakotagrafx said:mele kalikimaka
Must be on vacation. Or soon.
-
Merry Christmas to everyone!
Or, the same in whatever you believe in.
All the best.
- 3
-
http://www.graphteccorp.com/support/manuals/FC8000/FC8000UM2510.pdf
Go to 8.4.2. There is the error.
-
Flexi uses hpgl. Your second post is the firmware version.
Make sure there is nothing in the que waiting to cut. Unplug the usb and see it you still get the error.
If you don't get the error, the computer is probably still trying to send something in gpgl.
Y-Position Alarm issue
in GraphTec Cutting Plotter Support Requests
Posted
Cut a piece of vinyl off the roll and try loading a sheet. For some reason it is not measuring the width of the vinyl.