malachiind

Decals were done for a basketball travel team. 20 pieces, first two-color...Not as easy as I thought it would be. Wasted 3 doing the 20. By the way, what would some of you charge for this?

I hear ya! The space is probably larger than what it looks like. I used a square reg mark and just went for it, not bad for a virgin...

Sorry, Can't share image is copyrighted. For the three big windows and the door I charged $150 plus install. Install took about 2 hrs. This was my first one. I installed the three big windows dry and the door wet. Wet took a lot longer than I thought to dry out. Just used water, will have to add some alcohol next time to speed it up. Had to be real careful to remove mask as it wanted to pull up all of the vinyl, so then I had to wait some more and try again. All in all went pretty smooth with the dry, I think I'' stick to it for now.

Guess I lost out on a few $$$. I charged $10 for the artwork and then $8 ea.

The details of the pinup would cause the vinyl to start coming up. Tried all kinds of settings with better results, but not good enough. I needed the eyes to look good. Using the refine mh721. I think it was a combination of the vinyl and the cutter. Same vinyl on the summa worked a lot better, but still wanted to come up. Ended up cutting her seperately from the letters and worked perfectly.

Oops, sorry. 12" x 6"

UPS shows a week for ground delivery and $15 Let me know. Thanks

I love it... Went back to Missouri last June for a family reunion and my brother set his up...great way to pass time. Those look great.

I can turn it in a day, but then you have shipping, so it depends on where you are. I am in So. Cal. You? ...

I can get it to you for $4 sq/ft digitally printed with sewn hem and grometts.

Anyone have a nice diamond ring lineart? Thanks

Thank you very much.

Here is the pic...Let me know what you think.

I finally got it to work, but it still freezes after cutting. I am also trying to cut some thermoflex and it puddles up a lot when the blade is trying to cut. Anyone have any work arounds for this. I just tried to cut on a friends summa cutter and had absolutely no problems. Hope I can figure this out. thanks for the help

Yes, I am using the usb cable, but have had no problems up to this point. As for the baud rate etc...where do I change that. It's been a while since I set it up and don't remember any of that stuff.

I should probably also mention that it freezes up and won't respond either.

is this what you need?

Here is what I came up with. Looks like it will cut clean and nice. good luck fccustoms.eps fccustoms.eps

You could try and reheat to remove, have been able to only once before and was quickly after pressing or you could go to your supply shop and get a spot removing gun. Has some solution in it and sprays at high pressure, make sure to adjust so you don't blow a hole in the shirt. Spray from the back side and it should loosen the adhesive enough to get off. No guarantees though.

Those are some good ideas, I am waiting to hear back from the client on what it is he actually wants, rather than trying to figure it out. I appreciate the help and will show you the final product once it is done any more ideas are welcomed. Thanks

I have a client that travels on a basketball team. Team Name is Down Low. They want graphics for the vehicles and possibly jerseys. Something original. I am at a loss for any ideas, anyone willing to help out? Thanks

Mens traveling team, No established colors or at least willing to change. Been doing it for about 15 years. Just doesn't want the typical. Started out as friends and turned into a traveling team, most of the older guys are getting too old and so they are building it up with some younger players. Thanks

Thanks...

What type of vinyl do you use for interior walls. I have a few designs that my wife wants me to do and I just haven't had time to look into what type of vinyl would work best. Thanks,

Here is my business card. Although it has a lot of info, I think it looks clean and professional. I have actually gotten several printing jobs because of the quality. Don't really make a bunch on it, but every little bit helps.