Glass Blaster
Members-
Content Count
12 -
Joined
-
Last visited
-
Days Won
2
Glass Blaster last won the day on November 19 2021
Glass Blaster had the most liked content!
Community Reputation
3 NeutralAbout Glass Blaster
-
Rank
Member
-
Creation PCUT CTO1200 Cutting Strip
Glass Blaster replied to Glass Blaster's topic in Creation PCUT Cutting Plotter Support Requests
I needed 1.2 metres this is a 3 metre roll. https://www.aliexpress.com/item/10000001102416.html?spm=a2g0o.productlist.0.0.45ed3f6130sxw5&algo_pvid=eb9993c2-387b-46aa-b203-9a5d2a16c7c0&algo_exp_id=eb9993c2-387b-46aa-b203-9a5d2a16c7c0-9&pdp_ext_f={"sku_id"%3A"12000015814857766"} -
Creation PCUT CTO1200 Cutting Strip
Glass Blaster replied to Glass Blaster's topic in Creation PCUT Cutting Plotter Support Requests
Job done for US$5.50 using an 8mm wide strip & 6mm wide 3M double sided tape; the tape sat in the groove nicely. Thanks for all your help & suggestions. -
Creation PCUT CTO1200 Cutting Strip
Glass Blaster replied to Glass Blaster's topic in Creation PCUT Cutting Plotter Support Requests
It's only a hobby that is paying for itself so I may just bite the bullet as a last resort; retired so I'm in no hurry. -
Creation PCUT CTO1200 Cutting Strip
Glass Blaster replied to Glass Blaster's topic in Creation PCUT Cutting Plotter Support Requests
Thanks for the link, I've sent them an email, if that fails I purchase one from USCutters OR may try a modification I have in mind. -
Creation PCUT CTO1200 Cutting Strip
Glass Blaster replied to Glass Blaster's topic in Creation PCUT Cutting Plotter Support Requests
Unfortunately it' not worth flipping as it's quite damaged at the other end also. I purchased it second hand last year and it has been ok up until now. -
Creation PCUT CTO1200 Cutting Strip
Glass Blaster replied to Glass Blaster's topic in Creation PCUT Cutting Plotter Support Requests
US$73; AU$97!! for two delivered to Australia. I'll search a tad longer here; at least I know that they are available. Cheers all. -
Creation PCUT CTO1200 Cutting Strip
Glass Blaster replied to Glass Blaster's topic in Creation PCUT Cutting Plotter Support Requests
Yep. I pretty well gave up all hope until I discovered that it's the same as the USCutter LaserPoint and joined this forum. -
Creation PCUT CTO1200 Cutting Strip
Glass Blaster replied to Glass Blaster's topic in Creation PCUT Cutting Plotter Support Requests
Cheers, that appears to be the one although difficult to see the end profile. That certainly didn't come up in my searches maybe because I'm in Australia; I'll contact them to see if they'll post one (or two) out. Thanks again. -
Creation PCUT CTO1200 Cutting Strip
Glass Blaster replied to Glass Blaster's topic in Creation PCUT Cutting Plotter Support Requests
Thanks for the link however I have seen those & the strips on eBay but can't find one that matches mine Someone has the answer, I just haven't found it yet. -
Glass Blaster started following Creation PCUT CTO1200 Cutting Strip
-
Creation PCUT CTO1200 Cutting Strip
Glass Blaster replied to Glass Blaster's topic in Creation PCUT Cutting Plotter Support Requests
I did think of that as I was removing it but "No" because the profile doesn't allow me to; see attached photo. -
Creation PCUT CTO1200 Cutting Strip
Glass Blaster posted a topic in Creation PCUT Cutting Plotter Support Requests
Hi, my Creation PCUT is identical to the USCutter LaserPoint and has a worn cutting strip that I need to replace. I can't seem to find the correct part as any replacement strips all appear to use double sided tape whereas mine sits in a groove without double sided tape or glue. Does anyone know where I can purchase a new strip or is there a suggested modification as in purchase a generic cutting strip and attach double sided tape to that? Any help or suggestions would be much appreciated. Googling hasn't helped. Thanks in advance.