Donnie
Members-
Content Count
33 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Everything posted by Donnie
-
If your still interested in a base for edge lit acrylic sign I can show you what i make for my edge lit signs. Donnie! Do you have a cnc machine.
-
Can someone tell me how to place a decal on a license without getting tiny bubbles. I cleaned the plate with Isopropyl Alcohol wiped dry let it set. Then i placed the decal where i want it then i put tape across the top of decal. Pulled the backing off slow while holding the decal out the i started squeeging the decal slowly. Then when i would start pulling the transfer tape off laying flat down on the plate pulling slow I still would get little bubbles what am i doing wrong.
-
I'm starting to think it is the oracal 651 Burgandy vinyl giving me the problem. I tried everything to go about laying the app tape down squeegeing and still small bubbles. When I put the Oracal 651 white down no problems at all. Thats why I think it is the vinyl.
-
Ok Thanks I'll try this and let you know getting ready for the super bowl.
-
Skeeter what kind of paper tape do you use, could you see threw it to line the grafic up. I did lay the the decal on a flat surface then i put the transfer paper on. I bow the transfer paper in the middle. Wildgoose I squeegee the hell out of it the bubbles are smaller than a flea. There isn't that many but still i don't like it. Thanks i will try this do you buy this from US CUTTER
-
Thanks for the post very good info maybe this will help me.
-
Skeeter what kind of paper tape do you use, could you see threw it to line the grafic up. I did lay the the decal on a flat surface then i put the transfer paper on. I bow the transfer paper in the middle. Wildgoose I squeegee the hell out of it the bubbles are smaller than a flea. There isn't that many but still i don't like it.
-
Ok thanks I didn't think you could. I just wish I can that those pesky bubbles out ther very tiny but I don't like them. I think i'm doing the application the right way. Skeeter what kind of paper tape do you use, could you see threw it to line the grafic up. I did lay the the decal on a flat surface then i put the transfer paper on. I bow the transfer paper in the middle. Wildgoose I squeegee the hell out of it the bubbles are smaller than a flea. There isn't that many but still i don't like it.
-
Ok thanks I didn't think you could. I just wish I can that those pesky bubbles out ther very tiny but I don't like them. I think i'm doing the application the right way.
-
Ok thanks I didn't think you could. I just wish I can get those pesky bubbles out ther very tiny but I don't like them. I think i'm doing the application the right way.
-
I'm using the clear AT75 R-Tape would that matter if i would use application fluid on this tape. Idid try this and the addhesive got gummy.
-
Just recieved my graphtec ce6000-60 and cut a few heat transfer grafics And i took notice ther is a small line on the cutting strip the length of material being cut The cut weeds fine and it is not cutting threw the carrier sheet so is this normal. I'm cutting fashion film from Stahls The settings are Force=10 offset=1 speed=35 acceleration=1 Any help i would appreciate Thank you Donnie I just want to make sure i'm not damaging the cutting strip.
-
Ok i will try this tomorrow and let use know . Thank you Donnie!
-
Sorry i didn't get back to everybody. Cutting strip ok thank you. But now having a new problem after cutting a good bit of decals with oracal 651 I took notice the vinyl was starting to lift in the corners like it wasn't cutting through the vinyl. So i put a new blade in which i tried a cleancut blade still having problems. The settings are force=10 speed= 35 acceleration=1 offset=+1 also now the vinyl isn't weeding good. I also took notice the rounded curves in the O'S the D'S ISN'T CUTTING SHARP. What could that be. Donnie!
-
It isn't cutting threw the carrier sheet just scoring it.
-
Dakota! I guess what i'm trying to say is if the blade was cutting to deep wouldn't it cut right threw the carrier sheet. All i see is the score mark on the carrier sheet but it is not cutting threw. It is cutting threw the vinyl but just scoring the carrier sheet but not threw it.
-
Dakota! I guess what i'm trying to say is if the blade was cutting to deep wouldn't it cut right threw the carrier sheet. All i see is the score mark on the carrier sheet but it is not cutting threw. It is cutting threw the vinyl but just scoring the carrier sheet but not threw it.
-
What settings would you use to cut oracal 651 using the Graphtec ce6000-60 The machine is brand new.
-
Merry Christmas everybody! I hope you all have a very Merry day. Donnie!
- 1 reply
-
- 2
-
If your still interested in a base for edge lit acrylic sign I can show you what i make for my edge lit signs. Donnie!
-
Thanks a lot i did get it. I want to thank all of you for your help. Thanks Donnie!
-
How would you go about making a sign just say 12x8 I want the top one third part of the sign solid red with the text reverse filled. Then the rest of the sign in a red border outline. Thank you Donnie! I'm sorry i have VMP version 4
-
Ok thank you very much. Donnie!
-
Ok thanks a lot. Donnie!
-
I will try this it looks like would work I did say i have vinyl master pro version 4