pete00
Members-
Content Count
16 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout pete00
-
Rank
Member
- Birthday 01/01/1
Profile Information
-
Gender
Not Telling
-
Location
massachusetts
-
Is 33m too thick for a copam 2500 ? pete
-
pete00 started following Copam 2500 and Anchor Stencil 116
-
Howdy I have CP 2500, has anyone cut Anchor Stencil 116 with cp2500 Or is it to thick? thanks.....pete
-
copam 2500 only likes the usb serial cable that came with it
pete00 posted a topic in Copam Cutting Plotter Discussion
howdy I know this cant be true but.....i cant get the plotter to work with any other serial cable other than the usb/serial cable that came with it. Tried other cables, usb to serial, regular serial all to no avail. I know what your thinking but i did chage my medications. Be gentle with your comments..... -
howdy any comments on cocut......thanks pete http://www.cocut.com/index.dml
-
howdy similar question, took a look at the vinylmaster pro demo, look pretty good. anyone using it on the copam 2500 the 2500 is not listed in the supported machaines, left message for there tech support but no reply yet. thanks..............pete
-
free plug in for illustrator to print direct to plotter
pete00 posted a topic in Other Software Programs
howdy came accross this site, not sure if its any good or not, so i thought id send it to the experts here to check out.............pete http://www.magisign.com/US/SignNCS/Sign_dwld.html -
neebee question 3456B .........Wet application used on all vinyls ?
pete00 replied to pete00's topic in Vinyl
dear diary i may have found a few more folks for our therapy group, I will keep us posted........... me and him -
neebee question 3456B .........Wet application used on all vinyls ?
pete00 replied to pete00's topic in Vinyl
thanks for the info..................pete -
howdy all Can you use the wet application method on all vinyls without affecting the "stickiness" While i got you here, what the best way to remove vinyls from glass, razor and ? thanks for the help.................pete
-
thanks all, it doesnt seem to do it all the time, yesterday it didnt do it until the end of a sign. Ill just set it a little higher in the holder. thanks...pete
-
howdy been only playing with cp2500 for a little bit, but when i put in the pen holder lately its dragging accross the paper making lines. It didnt do that in the begining. i put a credit card under the pen and then tighten pen that stopped the draging but is something else going on. I power off and do the test but still drags. Havnt cut any vinyl today so i dont know if it will do it on that as well. Still practing with pen and SB. thanks....pete
-
thanks Jay It happens with most of the images ive been trying. Im sure SB is doing the right thing, in some other projects ill need the two lines but in a few i dont. SB sees the line and wants to draw the outline (2 lines), guess i need to figure out how to tell SB no matter how wide the line is just cut once in the middle......lol Lets see, mabey ill confuse you more by trying to show you what im up to. Heres a simple picture that i blasted on some glass. I put the picture on some paint mask then hand cut with exacto knife on the lines. I hand cut on the lines, then i pull each piece off and blast it. I make the seams by blasting a little deeper on each line. Even though the lines in the original picture may be thick, i only need to cut it once, dont need the outline. thanks again.....pete
-
thanks for reply jay i dont have the file here but i was able to create something. Pretend i just want to cut a trianlge out of a piece of vinyl. I drew the triangle in photoshop and saved it as a bmb, imported it, changed mode, and vectorized it. If you view it normal it shows a single line, it you view in outline/wire frame i shows up as two lines ( a triangle in a triangle ) sending it to the plotte will cut two lines. this make sense..... thanks....pete test line.SBD test line.SBD
-
howdy.. newbee here, finally figured out how to bring image in and send to plotter. Sorry if i dont know the right words to use but if i display an image in outline/wireframe for each line it shows two lines. Guess it has something to do with the width/stroke/offset ? of each line. But i need to cut some things with only one line between shapes......how do i do that. What words do i look up in the help section to show me...... or is it something i need to do in illustrator before i bring the image in. thanks....pete
-
Tykite im in as well, let us know how and when to pay...