Batranger

Does any one know if the workforce 1100 can print on mylar such as the Print me -Balloons

congrates Stetson!

batranger

batranger

can any one tell me how to print at the max size (I think it is 13''x44'') it's not in the list of sizes,read somewhere about the user define choice ,but don't know how to use it Thanks for any help

Sorry it seems I forgot to take my brain out of the jar this morning, I got it,thanks anyways

lets say, totally hypothetically of course , you go to open the new roll of 15" x 10 yds white FDC 4200 Series 5 Yr. Sign Vinyl you ordered and instead of being that it is a 15'' x 10yd roll of Sisser heat transfer vinyl ! Do you........ A) Call them and B***H cause the idiots sent the wrong S**T because you really needed the white vinyl..... B)Call them and tell them they made a mistake...... C) Tell the guy with the wings on your right shoulder to Shut the F**K up and order another roll of the white vinyl.......

Yes I did know the right thing to do,Just wanted to share a little humor. And Roxanne, oh never mind, my head hurts already from talking to the wife

@Batranger Is the Siser more expensive than the FDC 4200? (I know the price on 4200 but I've never priced out Siser) Will you use the Siser? Yes by about 3 or 4 times and I will use it sent an email to costumer service before I posted on here. Just got reply that since the order was actually 3 weeks old there was nothing they could do about the mistake,said I should have contacted them as soon as I got the order. Oh Darn now it's my fault

nice,looks good

very nice shirts

I printed this with my workforce 1100 on avery sticker paper,then sandwiched it between two pieces of clear fdc vinyl

thanks every one Hears a banner I did the same way

I open the pic with ps and adjust brightness (turn down a little) contrast (up a little) resolution change to about 600 or so ,then use filter-sketch-stamp. some times I have to go back and fort adjusting things thanks for the comments

One is my grandson, one is one I did of my son and his family.the other is my brother. I cut the vinyl with my mh721, and used etchall etching cream

Try changing the resolution,brightness/contrast,I have found that by doing this I can make a decal out of all most any picture This is one I made before I got my cutter, don't have a vector because I printed,traced, and hand cut

I had made a pissing Calvin magnet and put it on the back of my truck, I would make little magnets to piss on ,what ever pissed me off, Line Dancers,Union Maintenance Workers,Texters, whatever well first some one stole Calvin and the little magnet of a broken heart,so I made Calvin a decal, but someone kept stealing the little magnets ,till one day my daughter suggest I make one that said "Magnet Thieves" it stayed there for about 2 months till I felt safe to try a different one, next morning that one was gone.

live a block from elementary school, I just find it funny that they don't steal the Magnet Thieves one

To replace the z-chip: Turn over cutter, there are 2 plates on bottom we want to remove the smaller one. Remove 4 larger screws around edge and 2 feet. Lift up plate enough to unplug connectors. Cut wire tie holding wire to fan post. The z-chip is under the fan,(the one by itself) so we have to remove the fan. Remove the 4 screws holding board to plate ( THE WHITE SPACERS WILL FALL OUT) Remove nuts holding fan to board, set fan aside. Chip should have a dot or mark of some kind in lower left corner, in any case just make sure the lettering is going the same way and you should have no problems. To remove the old one pry up on ends with tweezers or small screwdriver, align pins on new one with socket and press gently to seat chip, making sure all pins are in and none are bent under chip. Put back together is just the reverse. HINT put screws through plate and set spacers and the board on them and just tighten the nuts enough to keep them in place then go back and tighten them all, this will save time because you won

joined the form cause my cutter started acting up ,,kind of glad it did though found some real useful info here ,,just waiting on an answer to the ticket. Been tring to get a bisiness started about 6 months now, do a lot of cutting by hand but got a couple of large orders for shirts and bought a refin cutter (all I could afford right now)