vectorman

hallo mr herzog thank you for your qwestiong ill do all the tests asp

did somone had the courege to pluge the plotter (im my case 1351) into europe 220 pawer whithe no transfomator?

sorry bur whathell is cast vinyl?? is id differnt from the vinyl vinyl?

try to look in da font.com im not shor what zodiac mean

http://www.dafont.com/theme.php?cat=804 http://www.dafont.com/faux-snow.font

try to put dawon the preshor

vinyl sliding- well due to a lot of tuning in the mh like the feed roller tuning every single on of them +the sparkle-iron whell tuning {not a common tuning i had to use it ,u have to open the bottom of the plotter turn in upsidedawon and u have some screws on thespakl}and the knife adjustment all of those didn't make my mh to be perfectly tuned duo to that I'm suffering from a terrible twists and sllides that cause some vynile to get lost even when I'm cutting slaw and loose the vinyl from the roll ill never can trust that the mh will cut like 2meter long on 118 cm high it will always slide and any advise till be appreciate

o.k i read a lot of info in the forum about drifting i made some checks and i found out that my third wheel is loosen (if u pull out a paper or vinyl underneath it u can pull in easily not like the other 3 wheels) even when I'm tigthe, a lot the 2 screws of that particular wheel it drift around 4 cm along 2 meter always to the rigthe side , which is not a lot but my desayer is to make it less i line up my vinyl white caution sticker which actually parallel to the mh body so the cutting strip is in 90 degree my Guss is that there is a problem in the iron wheel maybe it is not level since i tuned it before(need to open the bottom of the plotter) feed rollers r well thigte if u move one they all move stiff any suggests?

due to my MH 1351 hallo everyone i knoe disappered for a whaill g its good to comeback ronen ++++++++COOMING SOON++++++++++++ compear roland camm 1 VAS mh 1351 by:me

i need to roll all the artwork to the end and then cut it off haw do i tune it

well i hardly use siseres in my placewhat im trying to say is that the mh -afther he finsh to cut he roll the vyinl all the way up to the staring point and not in the end piont when i think about it i guss its a softwear thing. lolken i need the speling check option

is it allawod to sell costum made honda suzuki ect. logos stickers for bikers? please help

i own 1351 and a ronald camm 1 im thinking to buy this one http://cgi.ebay.com/COREL-DRAW-GRAPHIC-SUITE-X4-FULL-VERSION_W0QQitemZ280287999871QQcmdZViewItemQQptZUS_Software?hash=item280287999871&_trksid=p3286.c0.m14&_trkparms=66%3A2%7C65%3A16%7C39%3A1%7C240%3A1318 will it work whithe my plotter?

does coral x4 work whith th mh?

someone ever try to cut adhesive cork???

you have your stayle

someone can recommend on velved flock vynil not for haet press but normal glou like in the rgulalr vynil?? i need a good qwelaty the one u can cut in the plotter

x -film chrom made in u.k !?

u can allso find tryangel long and nerrow in e bey(tryangel caboard) u get it clean and u can stick your logo on it i dont know the sizes ull have to check

5-6 houers to install just becouse it was may first nexs tine should b much faster just remove the strip get it wet place it im the most easy place u think ,wipe it use heat gun(8.5 $ in e bay..) for the edge and u r finish

;Dwell some will sys its a zebra i think its an easy way to warp a sar whith u do it strip by strip no app reqwier on wet in that way u can avoid un neccecry handel ligth and all the placece u identify hard work... ofcors it is suteebul for mitshosishi magnum but im sure it culd be ajust enjoy p s this is a butifull link lets keep it VCRMAN.EPS VCRMAN.EPS

a small gift VCRMAN.EPS VCRMAN.EPS

the costumer sais that he really think the car runs faster

u know the iron box u lock and put your gold in

;) thanksx3