engraveanything
Members-
Content Count
15 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout engraveanything
-
Rank
Member
-
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
When I connect the USB to my computer, it only recognises as Keyspan new hardware, not the cutter is this normal?, secondly when I transfer the files to the cutter the Keyspan LED is very active, how much time does it take to transfer 10 letters of 3" size in times new roman?, third question on the far end to the display cutter has red switch what is this for?, the Error I am getting is CANNOT OPEN OUTPUT DEVICE ERROR INITIALIZING THE CUTTER" am I doing anything wrong here? thanks for the replies -
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
I tried all com ports from 1,2,3,4 and used generic drivers it transfers to cutter then the error in cutter response, looks like still can't find right drivers Thanks Sam -
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
It says com2,com3,com4 occupied, still I set it on com port 2 and software transfers to cutter but cutter does not respond, any other suggestion? -
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
Hi I tried with keyspan, after few minutes it says cutter not recognized? Called up the ordway, they are trying to sell new one -
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
Thanks, will revert Sam -
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
The Generic one didnt work, I even tried CM24 -
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
Thanks will try today -
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
Thanks you Mz, but one question which driver should I use from the list?, yes indeed there are some rollers and some clamps at the rear, i didnt take that picture the vinyl is held properly and even advances a bit whenever I start the cutter, looks like good condition but dont know much. if you can advice me which driver should I use? http://support.uscutter.com/index.php?/Knowledgebase/Article/GetAttachment/190/24198 -
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
I just realized mine doesn't have USB, it has parallel connections and I guess like a printer port, attached here with some pictures, can some one help me please? -
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
Thanks, will try and revert -
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
Now I am confused, but when i checked with Lancer this morning they told me it is easy cut 2009 model and no longer sell this product, so could it be gcc24? -
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
it is like the first one , Easy cut -
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
exactly like this ): you guys are so help ful, it has a stand, can you help me how to get this going? -
Easy cutter purchased from lancer group
engraveanything replied to engraveanything's topic in Creation PCUT Cutting Plotter Discussion
yes the model is EC-05, serial number is 5043-90, i ca post the picture but may be tomorrow -
Easy cutter purchased from lancer group
engraveanything posted a topic in Creation PCUT Cutting Plotter Discussion
Hello, I am new to Vinyl, as a hobby I bought this second hardly used machine with all the starter package, it cam e with two dvd's I thought it had the drivers, when reaching home I realised that it is missing the driver, contacted the company which sold this, they seem to have discontinued this product and I am stuck, it is 24" that's all there on the label. Can some one help me, i tried few drivers as per the seller( who seem to have no knowledge and he has spent all the money i gave), I am kind of stuck any help will be appreciated. thnaks Sam