GraphTec Cutting Plotter Discussion

484 topics in this forum

1. Craft Robo Info

   By BannerJohn, September 18, 2008
   • 5 replies
   • 11,370 views
   • 
   • aguilar
   • October 18, 2022

2. info from graphtec for cutmaster 3 and Graphtec studio

   By Dakotagrafx, January 23, 2017
   • 4 replies
   • 5,062 views
   • 
   • Dakotagrafx
   • January 26, 2017

3. Graphtec ce 5000-40 Not syncing with cutting master 3

   • 1
   • 2

   By yetna, April 17, 2015
   • 32 replies
   • 27,403 views
   • 
   • MZ SKEETER
   • April 30, 2017

4. Graphtec CE6000-60 Firmware

   • 1
   • 2
   • 3

   By Appleuser, February 5, 2015
   • 60 replies
   • 22,405 views
   • 
   • hkarns712
   • February 9, 2019

5. Graphtec CE5000-60 motherboard replacement

   By mikeguam, February 16, 2011
   • 22 replies
   • 21,628 views
   • 
   • jaybyrd
   • March 22, 2015

6. Graphtec CE5000 - 60 Load Media Message

   By albertramsbottom, September 18, 2010
   • 5 replies
   • 16,806 views
   • 
   • albertramsbottom
   • September 21, 2010

7. About to buy new CE6000-60

   • 1
   • 2
   • 3

   By theishkid, January 13, 2013
   • 52 replies
   • 15,558 views
   • 
   • Dakotagrafx
   • May 12, 2014

8. Can't connect to port Graphtec CE5000-60

   By Boom, June 23, 2014
   • 19 replies
   • 15,536 views
   • 
   • Boom
   • June 27, 2014

9. CE6000-60 Newbie issues, Curves & Cut Controller

   • 1
   • 2

   By terranomade, September 27, 2015
   • 35 replies
   • 15,022 views
   • 
   • MZ SKEETER
   • November 27, 2017

10. Ce6000-60 Perf Cut just cutting solid paths

    • 1
    • 2
    • 3

    By levy4u, December 13, 2014
    • 50 replies
    • 14,687 views
    • 
    • MZ SKEETER
    • January 11, 2015

11. Loading Media CE6000-60

    By wickedstangs, August 7, 2014   

    • Alighnment
    • 20 replies
    • 14,541 views
    • 
    • MK Creations
    • November 10, 2014

12. CE5000 vs CE6000

    • 1
    • 2
    • 3

    By JHew84, December 19, 2013
    • 51 replies
    • 13,546 views
    • 
    • Ninja
    • May 27, 2014

13. GraphTec offset problems

    • 1
    • 2

    By sidxyz1, January 5, 2011
    • 29 replies
    • 12,549 views
    • 
    • NiteWalker
    • February 16, 2011

14. CE6000-60 help

    By tmalone26, June 13, 2015
    • 19 replies
    • 11,974 views
    • 
    • Dakotagrafx
    • January 13, 2017

15. Graphtec CE7000 Push Rollers

    • 1
    • 2
    • 3
    • 4

    By ECombs, July 19, 2020
    • 99 replies
    • 11,485 views
    • 
    • slice&dice
    • May 21, 2023

16. GraphTec FC3100-60 & SignBlazer - HELP! I can't get them to work together.

    By DeonCarpenter, December 12, 2011   

    • GraphTec
    • FC3100-60
    • (and 1 more)

      Tagged with:

      • GraphTec
      • FC3100-60
      • driver SignBlazer
    • 16 replies
    • 10,581 views
    • 
    • sparkie_94
    • October 11, 2013

17. what is Novram Init ?

    By han7681, August 3, 2014
    • 12 replies
    • 10,108 views
    • 
    • Paulbasaloco
    • October 22, 2019

18. Cutter wont work on new computer...

    • 1
    • 2

    By gcextreme, March 16, 2015
    • 36 replies
    • 10,011 views
    • 
    • MZ SKEETER
    • March 18, 2015

19. New GraphTec CE-6000 24/40/60/120 Any Info on it?

    • 1
    • 2

    By NichoDesign, January 7, 2013
    • 26 replies
    • 9,821 views
    • 
    • MZ SKEETER
    • February 4, 2013

20. Cutting small letters recommended settings

    By racert25, January 28, 2015
    • 12 replies
    • 9,591 views
    • 
    • levy4u
    • January 29, 2015

21. Graphtec CE6000-60 problems

    • 1
    • 2

    By MadHatterGraphix, August 7, 2015
    • 26 replies
    • 9,373 views
    • 
    • MadHatterGraphix
    • August 7, 2015

22. Graphtec CE5000

    • 1
    • 2
    • 3

    By ramy, August 25, 2010
    • 55 replies
    • 9,338 views
    • 
    • Rodger
    • June 1, 2011

23. Vinyl slipping/weeding line cutting through image

    By jhumbeutel, August 3, 2011
    • 15 replies
    • 9,213 views
    • 
    • vinylmotivations
    • April 25, 2012

24. GraphTec Cameo VS Craft ROBO

    By dapparel, October 25, 2011
    • 5 replies
    • 8,785 views
    • 
    • dapparel
    • October 28, 2011

25. Best Software for Graphtec CE500-60

    By jhumbeutel, September 25, 2012
    • 13 replies
    • 7,744 views
    • 
    • Boom
    • June 28, 2014