USCutter Refine Cutting Plotter Discussion

811 topics in this forum

1. MH721 Set-Up on Mac - Driver Software? - Detecting and Installing Cutter

   By TEXASS, July 5, 2010
   • 6 replies
   • 17,197 views
   • 
   • jon521
   • January 17, 2013

2. Best software for mh721???

   By j4str, February 22, 2011
   • 13 replies
   • 15,115 views
   • 
   • Dakotagrafx
   • November 28, 2019

3. Windows 10 support

   By uncivil, August 23, 2015
   • 14 replies
   • 14,171 views
   • 
   • nnancyyta
   • June 28, 2016

4. Grounding?

   • 1
   • 2
   • 3

   By captonzoom, September 19, 2008
   • 52 replies
   • 14,005 views
   • 
   • Dakotagrafx
   • May 21, 2014

5. MH 871 Driver help

   By eat5, October 3, 2011
   • 14 replies
   • 13,870 views
   • 
   • MZ SKEETER
   • October 4, 2011

6. Cutter stopping mid cut

   By kfgreen, March 29, 2010
   • 19 replies
   • 13,470 views
   • 
   • MZ SKEETER
   • November 29, 2018

7. MH721 connection problem

   By Fredk, September 12, 2014   

   • Connection MH721
   • 18 replies
   • 13,028 views
   • 
   • slice&dice
   • September 17, 2014

8. MH721 problem, blade not lifting, z-chip?

   • 1
   • 2

   By b12yan12, January 21, 2011
   • 28 replies
   • 12,785 views
   • 
   • Kelmo66
   • January 10, 2018

9. Cutting issues. Bad cuts (Dove tails)

   • 1
   • 2

   By Hippie459MN, November 16, 2013
   • 36 replies
   • 11,885 views
   • 
   • Mike29610
   • January 19, 2019

10. wot driver do i use for my refine eh721 for use with flexisign

    • 1
    • 2

    By benb, February 23, 2007
    • 31 replies
    • 11,510 views
    • 
    • debmarsden
    • July 26, 2011

11. USCutter SC Contour Cutting

    • 1
    • 2

    By RBeaubien, May 17, 2013   

    • SC
    • Contour
    • (and 1 more)

      Tagged with:

      • SC
      • Contour
      • SCAL
    • 26 replies
    • 11,280 views
    • 
    • jaybyrd
    • September 30, 2013

12. Flexi STARTER P-CUT Edition is the problem

    • 1
    • 2

    By Belin, January 6, 2014
    • 33 replies
    • 10,838 views
    • 
    • jaybyrd
    • January 8, 2014

13. grounding cable?

    • 1
    • 2

    By SouthShoreDecal, October 9, 2009
    • 25 replies
    • 10,830 views
    • 
    • Dakotagrafx
    • September 7, 2010

14. Suggested Force for MH 871

    By sspvinyl, September 14, 2009
    • 9 replies
    • 10,081 views
    • 
    • VendettaVinyl
    • September 20, 2009

15. My impression of the Refine MH721

    By BannerJohn, April 13, 2007
    • 18 replies
    • 9,064 views
    • 
    • mb20music
    • December 16, 2017

16. USB Device not Recognized

    By stormy, February 17, 2010
    • 7 replies
    • 8,726 views
    • 
    • thredz
    • February 23, 2010

17. MH871-MK2 Refine MH Series Power Plug Problem

    • 1
    • 2

    By swooshstaff18, March 11, 2015
    • 33 replies
    • 8,340 views
    • 
    • darcshadow
    • November 3, 2018

18. setting for adhesive vinyl on Mh 721

    By condors1, January 14, 2011
    • 6 replies
    • 8,199 views
    • 
    • deth502
    • January 15, 2011

19. MH 721 - not closing cuts

    • 1
    • 2

    By Vermonster, April 2, 2016
    • 34 replies
    • 7,941 views
    • 
    • Wildgoose
    • April 12, 2016

20. Problem solved! - MH series jagged diagonal lines

    By dirttrackin280h, June 7, 2013
    • 16 replies
    • 7,895 views
    • 
    • kboyte
    • May 15, 2014

21. Mh-871 mk2 freezing midjob?

    By Silverdirt, December 21, 2014
    • 23 replies
    • 7,630 views
    • 
    • Wildgoose
    • August 27, 2016

22. Mh 871 with flexi

    • 1
    • 2

    By Scotty, January 30, 2010
    • 49 replies
    • 7,470 views
    • 
    • Ninja
    • March 26, 2010

23. Install MH721 as a printer to cut from Inkscape

    By Jules62, September 24, 2017
    • 9 replies
    • 7,431 views
    • 
    • dcbevins
    • September 25, 2017

24. Can these plotters cut fine/small details?

    By muibubbles, February 13, 2012
    • 11 replies
    • 6,674 views
    • 
    • BannerJohn
    • February 13, 2012

25. Need help with pinch roller marks MH-871

    By denise025, March 14, 2011
    • 3 replies
    • 6,328 views
    • 
    • jeremySI
    • March 15, 2011