-
Content Count
28 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout coreycss21
-
Rank
Member
-
What is the correct name/term for this kind of vinyl work?
coreycss21 posted a topic in General discussion
Hey guys, So i'm new with all this vinyl stuff and i'm not sure what the correct term or name is for this kind of work i do. I called it a wrap but i'm pretty sure that not the correct name. I do a lot of work for race teams and i don't want to mislead my customers so what would you consider this kind of work coming out of a vinyl cutter? Thanks! -
What to use inplace of heat transfer paper?
coreycss21 replied to coreycss21's topic in Heat Presses
That's my bad haha yea the paper that goes inbetween. Do you guys think the parchment paper is good to use all the time since i sell shirts or should i order that special paper? -
Hey guys quick question. I can't find the heat transfer paper that my heat press came with. I need to finish hoodies tonight is there something else i can use in place of heat transfer paper? Thanks
-
Random lines cut when cutting and support has no clue...
coreycss21 replied to coreycss21's topic in Criticism and Complaints about USCutter
Ok I tried the serial plus but mine on my PC isn't a 9 point. Also I have anti static spray. How often do you guys spray it and where? -
Random lines cut when cutting and support has no clue...
coreycss21 replied to coreycss21's topic in Criticism and Complaints about USCutter
Yea i have all of that. Now it loves stopping mid cut. I'm not sure if it matter but i''m doing it on a higher end HP Portege laptop. -
Random lines cut when cutting and support has no clue...
coreycss21 replied to coreycss21's topic in Criticism and Complaints about USCutter
I pre cut the roll. My set up is on a wooden top and metal on the button and it is on a wood floor.I have the cutter grounded with the wire they send you and that is attached to the stand and the other end to the cutter. I wipe the heck out of the machine with dryer cloths and i also have the anti static spray and a very good ground. -
Random lines cut when cutting and support has no clue...
coreycss21 replied to coreycss21's topic in Criticism and Complaints about USCutter
I have tried everything. I just tried cutting a 3ft long sheet and it messed it all up once again! This is really getting frustrating! I contacted USCutter and i still have not gotten anyone to contact me back...... -
Random lines cut when cutting and support has no clue...
coreycss21 replied to coreycss21's topic in Criticism and Complaints about USCutter
Yea i always check over it a few times and nothing ever shows up i didn't want on. -
Random lines cut when cutting and support has no clue...
coreycss21 replied to coreycss21's topic in Criticism and Complaints about USCutter
Yes,I never let it pull from the roll i always pull it to the right length first. -
Random lines cut when cutting and support has no clue...
coreycss21 replied to coreycss21's topic in Criticism and Complaints about USCutter
Nope still no luck... This is so frustrating i even talked to the manager and all that happens is he tells me what to do then it happens again and again and i never get anywhere! Does anyone know of a higher up staff member from USCutter? -
Random lines cut when cutting and support has no clue...
coreycss21 replied to coreycss21's topic in Criticism and Complaints about USCutter
Yup, it still does it...... -
Random lines cut when cutting and support has no clue...
coreycss21 replied to coreycss21's topic in Criticism and Complaints about USCutter
Yea i have a ton of dryer sheet under the cutter and two in the roll and yes i also have a serial cable. -
Random lines cut when cutting and support has no clue...
coreycss21 posted a topic in Criticism and Complaints about USCutter
Hi guys, I was cutting a sheet of vinyl 20x15in and i notice when it was about half way threw cutting it cut a line threw the center and and in a few other spots several times. I'm using sure cuts a lot and my cutter is on a wood stand grounded and the model is the SC. After wasting 5 feet up heat transfer and basically throwing money away it still did it! And it also just loves stopping mid cut! After contacting customers service i explained the issue and was assured several times a call back but those calls never came..No offense to the staff but they seem to be clueless about they're products. i don't know if it's the cutter or what but this is my second SC because the first one came used(yes i ordered a new one so i thought) but it also came broke just like my current machine but i had to fix it. At this point i'm just looking for help from someone to fix this issue. I honesty thought USCutter would stand behind their products and value they're customers but as it looks it unfortunately doesn't look like that. -
Best way to apply vinyl without wrinkles or bubbles?
coreycss21 replied to coreycss21's topic in Vinyl
Haha i wish! From what i kinda studied and from what everyone seemed to say is if it's on a flat surface the 631 or 651 should work but if their is a lot of bends to use the 751. -
Best way to apply vinyl without wrinkles or bubbles?
coreycss21 replied to coreycss21's topic in Vinyl
Wrapping is probably not the right term but that's what i call it lol. This is what i mean when i say wrapping.