422 0 Posted September 27, 2008 I've been cutting hog wild, still with problems, but at least I'm cutting. So I've cut a handful of words only to find that when I was going to apply them to coroplast they seem to be backwards. It seems as though the cuts have been made for glass window application where they first appear backwards until one gets on the otherside and can read them correctly. I was desiring to apply to a solid backing. Can any one tell me if there's a setting that I may have wrong? Thank you. Share this post Link to post Share on other sites
Benr98 40 Posted September 27, 2008 As long as you don't have it mirrored, it should be fine! If you are cutting vinyl to apply to a surface, such as coroplast, window decals, etc...what you see, is what should be cut. Another thing, are you applying the app tape to the vinyl BEFORE applying it? Mirror for heat applied vinyl. Share this post Link to post Share on other sites
422 0 Posted September 27, 2008 after I applied transfer paper, i went to affix my words to coroplast and noticed that if I take off the white paper backing first and then hinge over top and rip off transfer paper, the words are reading reversed in some fashion either right to left or the letters are flipped whereas the 3 prongs of the letter "E" normally point to the right, they are pointing to the left, reversed. Share this post Link to post Share on other sites
Benr98 40 Posted September 27, 2008 What kind of software are you using? Jenny Share this post Link to post Share on other sites
422 0 Posted September 27, 2008 sign blazer trial version Share this post Link to post Share on other sites
Benr98 40 Posted September 27, 2008 All your letters are backwards?? Are you sure you don't have your image mirrored in SB?? Share this post Link to post Share on other sites
snlsd 1 Posted September 27, 2008 Post the file and we can take a look on our end. Share this post Link to post Share on other sites
422 0 Posted September 27, 2008 I'm not sure; when i clicked the mirror button it puts 2 lines on screen and seems to flip image, but then turns off; I only fooled with that when you mentioned it not sure how to post a file; i'll look and if it's wasting too much time I think I'm re-boxing this who thing and sending back to US Cutter; this just shouldn't be this difficult! Thanks. Share this post Link to post Share on other sites
BannerJohn 1,324 Posted September 27, 2008 I'm not sure; when i clicked the mirror button it puts 2 lines on screen and seems to flip image, but then turns off; I only fooled with that when you mentioned it not sure how to post a file; i'll look and if it's wasting too much time I think I'm re-boxing this who thing and sending back to US Cutter; this just shouldn't be this difficult! Thanks. send it back. If you think learning how to use complicated software is a waste of time,.you don't need it. Share this post Link to post Share on other sites
snlsd 1 Posted September 27, 2008 Click on "Additional Options" under the text where you post your message. Browse for the file and upload it. Share this post Link to post Share on other sites
Benr98 40 Posted September 27, 2008 Any software you aren't use to, is going to take time to learn...heck I'm still learning all the time. When you are in SB, if the image appears mirrored, that is how it will cut...you do NOT want it to show mirrored on your screen. Share this post Link to post Share on other sites
422 0 Posted September 27, 2008 trying to find file Share this post Link to post Share on other sites
422 0 Posted September 27, 2008 system is not taking file..says I took too long or file is too big....god nothing is straightforward appearance was normal on screen Share this post Link to post Share on other sites
422 0 Posted September 27, 2008 file is only 9kb, vs max 0f 1024kb LEASE-1x4.SBD LEASE-1x4.SBD LEASE-1x4.SBD LEASE-1x4.SBD Share this post Link to post Share on other sites
422 0 Posted September 27, 2008 when one reads the words they appear to read correctly (through white backing) but when you go to apply you can see that's it's almost as if the sticky is on the wrong side Share this post Link to post Share on other sites
422 0 Posted September 27, 2008 looks like file went through Share this post Link to post Share on other sites
Benr98 40 Posted September 27, 2008 Well there was nothing in your files. Sure you have the vinyl loaded correctly? It sure sounds like you are cutting the backing of the vinyl and not the top!! Share this post Link to post Share on other sites
422 0 Posted September 27, 2008 vinyl up, paper down Share this post Link to post Share on other sites
422 0 Posted September 27, 2008 just read through "Mirroring" in tutorial and it requires opening a dialogue box, etc and I definitiely did not do that. OK, I guess some day i may figure out I appreciate your guys attempt to help me out Share this post Link to post Share on other sites
Benr98 40 Posted September 27, 2008 Sorry I couldn't help you more. It's really hard to tell without your file here to see what may be going on. Sounds like you have it loaded right....so you got me stumped, what could be going on there. Share this post Link to post Share on other sites
Benr98 40 Posted September 27, 2008 Hey one more thing: if it looks right but cuts mirrored... try CHECKING the mirror box and see if it comes out right. I have a feeling this is an easy fix...something is checked that shouldn't be. But just try it one more time. Thanks Share this post Link to post Share on other sites
Benr98 40 Posted September 27, 2008 If it already is unchecked...checking it will reverse it. See pic for better understanding............. Share this post Link to post Share on other sites
darkdan 3 Posted September 27, 2008 not sure how to post a file; i'll look and if it's wasting too much time I think I'm re-boxing this who thing and sending back to US Cutter; this just shouldn't be this difficult! This is why being a sign professional is a trade skill. Share this post Link to post Share on other sites
422 0 Posted September 27, 2008 didn't even know about that mirror option and no, it's not checked....I was looking at another mirror option under "manipulation" this is unreal Thanks for your help Share this post Link to post Share on other sites
422 0 Posted September 27, 2008 however, if it's not checked you're suggesting to check it, correct? Share this post Link to post Share on other sites