Recommended Posts

hola .....

necesito ayuda   tengo un plotter us cutter laser point que compre de segunda mano 

resulta que el plotter funciona desde los mando del plotter avanza,  retrocede, izquierda y derecha normal  realiza el tes, y realiza un troquel que tiene en la memoria 

pero cuando envió un trabajo desde flexi 10,   corta  pero siempre hace el mismo corte dos circulos  dentados .....envie lo que envie siempre hace los mismo 

puede alguien ayudarme  

IMG_0725.JPG

IMG_0726.JPG

IMG_0727.JPG

Share this post


Link to post
Share on other sites

Does the Flexi 10 have a USB dongle? Like a thumb flash drive that you have to put in your computer USB port to make Flexi 10 software open? Like shown in this picture?383009460_Flexi10legalwithdongle.jpg.8fdd2803f61ca015c555bcb3d824e50f.jpg

Share this post


Link to post
Share on other sites

Puede intentar descargar e instalar Sign Blazer Elements.  Es un programa gratuito.  Intente enviar un archivo a su cortadora usando ese programa y avisenos si el problema persiste. Esto nos ayduara a aislar lo que sta sucediendo.

Share this post


Link to post
Share on other sites
On 1/12/2021 at 6:18 PM, MZ SKEETER said:

Does the Flexi 10 have a USB dongle? Like a thumb flash drive that you have to put in your computer USB port to make Flexi 10 software open? Like shown in this picture?383009460_Flexi10legalwithdongle.jpg.8fdd2803f61ca015c555bcb3d824e50f.jpg

 

Share this post


Link to post
Share on other sites

Which Laser Point do you have? There have been 3 versions so far.

Turning it off and on, should clear any data that was sent to the cutter.

What happens when you try to do a test cut from the cutter panel?

Share this post


Link to post
Share on other sites

gracias .... creo que es el de laser poin de  24

al apagarlo y encenderlo no se borra ... el tes hace cuadro y cuadro adentro como la foto 

cuando se le da copy  rotula un troquel de una caja todo esto propio del plotter  y cuando se envia cualquier trabajo desde el computador desde el programa 

hace dos circulos dentados   SIEMPRE  se envi lo que se envie siempre hace dos circulos dentados 

 

gracias 

Share this post


Link to post
Share on other sites
On 1/14/2021 at 2:37 AM, haumana said:

Which Laser Point do you have? There have been 3 versions so far.

Turning it off and on, should clear any data that was sent to the cutter.

What happens when you try to do a test cut from the cutter panel?

Which Laser Point do you have? There have been 3 versions so far.

is laser point of 24

Turning it off and on, should clear any data that was sent to the cutter.

They are not erased in memory, a die is left from a box when the die is sent copied

What happens when you try to do a test cut from the cutter panel?

From the panel, if I send you tes, it makes two pictures one dendro from the other and if I give it a copy, it makes the die of the box

from the computer it always makes two jagged circles

Share this post


Link to post
Share on other sites

I asked which version of the LP you had because the blade carriage looks different that mine - which is a 1st generation LP.

Doing the text cut from the panel should not trigger the jagged circles to cut, the test cut for the 1st gen LP is a simple rectangle. Trying disconnecting the communication cable from the PC to the cutter. Start up the LP, and try running the test cut from the control panel again.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this