slice&dice 2,450 Posted September 28, 2015 OK, sports fans, here's a thread that covers what USCUTTER is featuring prominently on their main website (and in advertisements here on the Forums) --- Vinyl Master Basic, the $29.95 "upgrade" to whatever you're currently using to cut with. While waiting for my order to be processed (am I going to get an actual physical disk, or just a serial number and a downloadable installer?) I wanted to cover a few of the reasons I decided to pay for this program. 1. Clipart included. As I looked at the screenshots, it became readily apparent that there were many items in the clipart library which caught my interest -- outstanding among them is the Grateful Dead logo. 2. Fonts. I'm hoping there's a good way to keep them catalogued, especially with thousands of styles. 3. Vectorize engine. 'Nuff said. 4. User-friendly interface and low learning curve. 5. No Limit on number of computers it can be installed on (I have four currently which are used for designing). As I get involved with using it (later this week, after delivery and installation) I'll offer further comments and reviews. Share this post Link to post Share on other sites
Wildgoose 4,200 Posted September 28, 2015 outstanding among them is the Grateful Dead logo. Ha ha! Share this post Link to post Share on other sites
Go-C Graphics 856 Posted September 28, 2015 OK, sports fans, here's a thread that covers what USCUTTER is featuring prominently on their main website (and in advertisements here on the Forums) ---Vinyl Master Basic, the $29.95 "upgrade" to whatever you're currently using to cut with. While waiting for my order to be processed (am I going to get an actual physical disk, or just a serial number and a downloadable installer?) I wanted to cover a few of the reasons I decided to pay for this program. 1. Clipart included. As I looked at the screenshots, it became readily apparent that there were many items in the clipart library which caught my interest -- outstanding among them is the Grateful Dead logo. 2. Fonts. I'm hoping there's a good way to keep them catalogued, especially with thousands of styles. 3. Vectorize engine. 'Nuff said. 4. User-friendly interface and low learning curve. 5. No Limit on number of computers it can be installed on (I have four currently which are used for designing). As I get involved with using it (later this week, after delivery and installation) I'll offer further comments and reviews. Are you sure about this one? I can't use my Pro version on multiple computers. Share this post Link to post Share on other sites
slice&dice 2,450 Posted September 28, 2015 Are you sure about this one? I can't use my Pro version on multiple computers. Yep. From the description on the website --- LicensingWhile cutting with VinylMaster Cut is limited to one user, use of the software is available to unlimited users. Your design team...and vinyl cutter specialist can all collaborate using one license and send the cutting file to the computer connected to your cutter when it's time to actually cut the job. This allows you to design and work from any location. 1 Share this post Link to post Share on other sites
Sue2 920 Posted September 28, 2015 Slice...that room is WAY too neat! You can't be doing any real work there..... Sue2 3 Share this post Link to post Share on other sites
slice&dice 2,450 Posted September 28, 2015 You think the design area is neat & tidy, you should see the sign-assembly portion ---- (12-foot-length weeding/taping/dropping table) 1 Share this post Link to post Share on other sites
Sue2 920 Posted September 28, 2015 LOL...you DON'T want to see a picture of my space! 2 Share this post Link to post Share on other sites
jaybyrd 3,770 Posted September 28, 2015 I can run xpt on dozens of pcs BUT you cannot cut, export or print from them only the one activated at the time. You can save in native format though to open at your cut station so it basically gives you limitless design stations. Share this post Link to post Share on other sites
slice&dice 2,450 Posted September 28, 2015 Another good reason for having this software is the Text-Along-Path feature, which SignBlazer doesn't handle (it is greyed-out in the Elements version we use, because it was an item only for the HotShot/Pro version). And, unlike SCAL, the VMC program allows for multiple lines of text by just hitting the ENTER/RETURN key. I never understood why SCAL did not get that. 2 Share this post Link to post Share on other sites
mr300s 1,272 Posted September 28, 2015 Glad you going to keep us posted I was thinking about that program but didnt want to pay $300.00 to try it Share this post Link to post Share on other sites
MadHatterGraphix 1,258 Posted September 28, 2015 I'm hoping this stays on sale till Friday when I can purchase it but doubting that it wills till be on sale. Share this post Link to post Share on other sites
Go-C Graphics 856 Posted September 28, 2015 I can run xpt on dozens of pcs BUT you cannot cut, export or print from them only the one activated at the time. You can save in native format though to open at your cut station so it basically gives you limitless design stations. That's my problem. I need to be able to export as a .plt to while on my laptop in the garage to send to the laser. Damn i got excited for a sec. Share this post Link to post Share on other sites
jaybyrd 3,770 Posted September 28, 2015 What you need to do is buy the cheapest version you can to run on the laptop. I would think that would do it but more homework may be required. Share this post Link to post Share on other sites
mr300s 1,272 Posted September 28, 2015 So will this work by itself or is it a upgrade if you already have it which I dont? Share this post Link to post Share on other sites
Primal Decals 621 Posted September 28, 2015 Is this upgrade worth it over my scalps 4 software for $30? is it better or a waiste of money.I use Ai to design in and scalps 4 for doing shadows or minimal tweaks etc and to cut final project. Thanks Share this post Link to post Share on other sites
MadHatterGraphix 1,258 Posted September 28, 2015 So will this work by itself or is it a upgrade if you already have it which I dont? System RequirementsPentium processor-based PC or compatible computer (Windows) Windows XP/Vista/7/8 (Windows) 512 MB of RAM or more At least 50 MB of available hard disk space USB Port 1.1 or 2.x Would think if it was an upgrade it would say a previous version of the software would be needed. Share this post Link to post Share on other sites
Sue2 920 Posted September 28, 2015 I believe US Cutter is offering it to those who have purchased cutters from them. This is an Upgrade for the programs we are now using (like SignBlazer etc). ...not a Vinyl Master upgrade requiring a previous version. Customer Service told me the $30 was a special email offer for US Cutter customers. If you go to the website the price is $59.95. Sue2 Share this post Link to post Share on other sites
slice&dice 2,450 Posted September 28, 2015 "If you go to the website the price is $59.95" The main page of their website has a huge banner ad right across the top, and clicking on that sends you to the promotional pricing page. As well, on the front page of this Forum, there's an ad which offers this deal. Click on it and you're there. Anyone can take advantage of the $30 pricing, all you need is to have a USCUTTER account. Also, I highly recommend that you bundle other items that you normally order (vinyl materials, banner blanks, app tape, coroplast, etc.) so the $9.99 flat shipping charge covers all the things you need, and not just the $30 program (making it $40 !!!) In answer to your question, PrimalDecals, I'm thinking the answer is a resounding YES !! USCUTTER knows very well that SCAL'pro' is not the ideal solution for their customers, and have apparently worked with VinylMasterCut to place this nice program into the hands of those who are frustrated or disappointed with that clunky CraftEdge product. There's a free demo version (no saving/exporting/cutting) that people can utilize to assess their interest in going this route. I didn't even bother with checking it out with a demo trial, and went ahead and already ordered the full version sight unseen (based on the screen shots and description). Of course, taking a 'test drive' is an option that you might want to pursue !! YMMV. 1 Share this post Link to post Share on other sites
skarekrow 1,842 Posted September 28, 2015 Not so sure about whether the Fonts and Font Manager are included with the "Cut" Version, Slice. VinylMaster_Comparison_V4.pdf Share this post Link to post Share on other sites
Wildgoose 4,200 Posted September 28, 2015 Uh oh, there goes the dead head stickers. Way to spoil his fun Skare. 1 Share this post Link to post Share on other sites
Primal Decals 621 Posted September 28, 2015 Thank you Slice&Dice.Awesome Will check it out demo just to see and go from there..Thanks Share this post Link to post Share on other sites
signyouup 178 Posted September 28, 2015 Not so sure about whether the Fonts and Font Manager are included withthe "Cut" Version, Slice. VmFontsClipart.jpg VinylMaster_Comparison_V4.pdf It is comparable to Signcut but with some very basic design tools. 1 Share this post Link to post Share on other sites
skarekrow 1,842 Posted September 28, 2015 I couldn't ascertain whether the dead head skull was in the 'Cut' package. It is definitely in the Pro. Share this post Link to post Share on other sites
Primal Decals 621 Posted September 28, 2015 just talked to uscutter....The cost is $30 for the upgrade for our Value Cutters, for Titans, its $45. just wanted to post this for titan owners Share this post Link to post Share on other sites
skarekrow 1,842 Posted September 28, 2015 That's my problem. I need to be able to export as a .plt to while on my laptop in the garage to send to the laser. Damn i got excited for a sec. You could save as a 'vDoc' (Vm's native format) and open it at your other (cutting) station with the activated version of Vm then Save as> a .plt file and cut from there. 1 Share this post Link to post Share on other sites
