Search the Community
Showing results for tags 'copam 2500'.
Found 7 results
-
copam 2500 PROBLEMAS DE CONFIGURACIÓN DE COPAM 2500 CON ARTCUT 2009
OXWAL posted a topic in General Help
Hi everyone I have a configuration problem with my Copam 2500 ploter. I was working normally so it occurred to me to disconnect the USB cable and connect it to my laptop to work from there to reconnect to my pc I did not cut I do not know what happened I have seen tutorials everywhere and I do not get a solution, could anyone help me?- 5 replies
-
- copam
- configuracio
-
(and 2 more)
Tagged with:
-
Copam not working now. Can someone chk motherboard
SewDarnHot posted a topic in Copam Cutting Plotter Support Requests
Hi, I have been out of commission for quite some time. My copam was josstled quite a bit when moved and now will not show the screen for more than a brief second. The screen will light up when turned on but will only light for a second and then it goes out. I tried all the connections, blew it, cleaned with electronic cleaner, I have checked all the soldering connections and do not see any breaks. Lots I have read lead back to the mother board. Is there anyone that I can send by motherboard to and they can check and see if that is the issue before I go buying a new one? -
Copam 2500 pressure problems
thewishingwall posted a topic in Copam Cutting Plotter Support Requests
I am baffled at my copam cutter. It makes a knocking noise when the carriage brings down the blade, which it has never done before. I tried plotting with a pen and it worked great and made no noise. It also won't cut at all uness it is on the lower pressure settings, which makes no sense at all. When I put it on the lowest pressure it will cut, but it skips spots in letters, like it doesn't completely come back to cut where it started (that's plain as mud ) When I up the pressure it starts out great, but after cutting a bit it is only barely marking the vinyl. Checked the cutting strip and it has no cuts. So, not sure what to replace.... the mother board, the carriage, the blade holder???-
- 1
-
- copam 2500
- pressure
-
(and 2 more)
Tagged with:
-
I am having trouble with uneven cutting using my Copam cutter. I am thinking it may be the cutting strip, as I have never replaced mine. Now for the stupid question....do I have to buy the actual part for the copam 2500 or are there "generic" cutting strips? I just don't want to spend $20 plus shipping and handling in case it is not the problem. I have read also where you can test it by using a pen??? Anyone know how to do that? Also I read where you can use reflective vinyl to replace your cutting strip? Know anything about that??? Thanks in advance!!!!
-
Help Please ... Having some issues cutting all of a sudden of curves, they look jagged and speckled not clean at all. Tried the blade offset from .20 to .40 with no change, tried 3 new blades nothing ... Have no clue what else to try . Any suggestions ? Blade offset is at 14 using copam 2500 and SCAL3 Pro
- 11 replies
-
- copam 2500
- copam jagged cuts
-
(and 1 more)
Tagged with:
-
I have a Copam 2500 and it has been working great for 5 years. When I started working on a decal order today, I noticed the control panel buttons were not working. When I press the "Setup" button nothing happens so I can't adjust the speed and force. If I press the "measure" button it doesn't respond so I can't measure my vinyl. Is there anything I can do to fix this problem? Will purchasing a new control panel from USCutter solve the issue or is time to get a new cutter since it is over 5 years old?
- 5 replies
-
- copam 2500
- control panel
-
(and 1 more)
Tagged with:
-
we just purchased a copam 2500 w flexistarter 10 software but my CD rom is acting up. is there an actual download for flexi i can use instead of disk.or equivalent software to get me up and running to play w this cutter until my other pc is repaired?any links would be great , Were new to cutting vinyl I did Flexistarter 10.0.4 downloaded but i have windows 7 and its saying incompatible application and sometimes it opens and says key did not match password? Same with production manager 10.0.4...i have signcut and inkscape as well...any suggestions...I have disk but until Dell gets my new cd rom sent im out....unless theres a flexi download avail or another equivalent software program for copam 2500.