lil craft shack

Members
  • Content count

    13
  • Joined

  • Last visited

Community Reputation

0 Neutral

About lil craft shack

  • Rank
    Member
  1. lil craft shack

    Is there a sealer to use...

    You rock thank you so much for all your help!!!! I was thinking of just doing 651 and not stressing it!!! Lol... Wish you could do it for walls too but that's a whole new battle I'll have to figure out now!!!!! So appreciate all your time!!!!!
  2. lil craft shack

    Is there a sealer to use...

    Ok that's what I've been reading.... I've been a wonderful help thank you... I've noticed the paper tapes are so much easier to work with instead of the clear ones... Unless your using them for a car window type decal....
  3. lil craft shack

    Is there a sealer to use...

    @skarekrow... I heard acrylic paints are the best... Do you seal that before vinyl goes in for better adhering???
  4. lil craft shack

    Is there a sealer to use...

    Well the signs for indoor I use 631 and outdoor is 651...
  5. lil craft shack

    Is there a sealer to use...

    Can I also ask a quick question about vinyl decals for wall adhering??? The oracle 631 is what I use for that as well... I haven't found a great transfer paper for this... All wants to hold onto the vinyl ... I've tried HT55 and GXF 100 .... I hope I labeled those right.... But those are what I'm reading are the good transfer tapes and they suck for me... Is it because some have had a gloss finish and others matte???
  6. lil craft shack

    Is there a sealer to use...

    I'm thinking the only signs I had a problem with were the ones I didn't use an acrylic paint as base.... I also noticed if I seal the wood with a mod podge or laquer it adheres better...
  7. lil craft shack

    Is there a sealer to use...

    Hi and thank you!!!! I use good paint and prep well... I use oracle 631... Is that my problem???
  8. lil craft shack

    Is there a sealer to use...

    I use a lot of my vinyl on wood and MDF painted boards and such.... After I apply the vinyl is there a sealer I can use over the vinyl???
  9. lil craft shack

    New Oracal Application tape for Oracal 631 vinyl

    Ok question.... I had read that people were using the GXF 100...( Hope I labeled that right... ) and I cannot get it to let the vinyl go at all!!!!! A little heat maybe???
  10. lil craft shack

    Text help with SCALP

    Real quick also... I did do the 90 degree rotation and my mats I use are all custom because I need it that way... When I start horizontal to create the image and it shows going to the cutter incorrectly then I rotate 90 degrees but it doesn't change the to the smaller way... It still would make it a 35 in cut horizontally... So I'm gonna try and do the group and weed box tomorrow!!!!! Thanks again.... Also what program do you all prefer to use with a MAC??? Illustrator???
  11. lil craft shack

    Text help with SCALP

    Thank you guys so much!!!! I think the problem is... When you can select your cutter... I select the new titan 2 and it doesn't give a size of the machine so it can assume that I have up to a 60 in machine to work with... Is this why it would do this also???
  12. God is great... Beer is good.. and people are crazy....

  13. lil craft shack

    Text help with SCALP

    Since all of you seem to really know SCAL... Can I throw a quick question in??? WHen all is said and done and you are ready to cut... It shows the orientation or way the machine is going to cut your decal... My cutter is 24 in and I am cuttin a 35 in piece and its showing it being cut horizontal which obviously cant happen... so I switch the orientation in mat orientation and it still cuts it horizontal.... how can i make it cut with the lease amount of width??? its a 35 x 5 in word and instead of it cutting the 35 in all across.. my vinyl is only a 12 in roll also... so i need it to cut longer...
  14. lil craft shack

    Got My Titan Yesterday

    Ugh I had all the same issues.... actually using it without my stand because I could't find instructions.... Finally figuring it out and I've had this about a month.....
  15. Prob a dumb question.... How do i change the cut orientation in SCAL3 ....