Bunky67
Members-
Content Count
22 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Everything posted by Bunky67
-
Does cutstudio have drivers to run older cutters ? I have an older pnc 1050 and had to upgrade to windows 10, if I purchase Cut studio will this have driver's to run my machine?
-
I have an old Roland PNC1050 I have been using on an old XP machine with Corel draw X6. The computer is getting tired so I wanted to buy a newer machine with Windows 10 and Currently have Corel Draw 17. I can't get the Windows 10 to install the XP driver's Is there a plug in or something I can do to get windows 10 to recognize this plotter?
-
Hello These cutters will work just fine on USB I use mine with Corel draw all the time. The problem here is they always want to send you to sign blazer, which is good if you don't have $$$ wrapped into other software. Do you have the MK1 or MK2? There are different drivers and chipset for the MK1 vs MK2. I pull my hair out when trying to install on a different computer but it does work. I assume your running windows does Windows see the cutter in device manager?
- 6 replies
-
- device not detected
- vinyl master pro
-
(and 2 more)
Tagged with:
-
My 871 was bought used and I have used it of course but the rubber grit rollers have a build up on them from being used and not cleaned properly... I tried a little rubbing alcohol on a rag and that took off some. But I need to get them better. Can I use goo gone or something similar? Also has anyone found a replacement roller for these without changing the whole roller unit ?
-
Older Roland and Windows 10?
Bunky67 replied to Bunky67's topic in Roland Cutting Plotter Support Requests
Well the machine was just old and I wasn't sure Corel draw 2017 would work and the xp machine wasn't starting properly some times -
I have a MH-871 MK1 and i was using it with Corel Draw x6, (yesI have cut straight from corel) well I upgraded to Corel 2017 and haven't used my laptop to cut since, ( I have a small roland tractor paper style I use on an old xp desktop) so the other night i wanted to cut a pattern out off the laptop and Corel Draw didn't show my cutter. So I went in and I see the cutter under my USB devices and it appears to be working according to device manager. can someone tell me how to get this listed back under my printers or set up so my corel will recognize it again
-
MH 871 with windows 10 ?
Bunky67 replied to Bunky67's topic in USCutter Refine Cutting Plotter Discussion
Yes Skeeter it was was basically the same issue, this time i had to go in and set up printer manually issue resolved -
A couple of weeks ago I installed my MH-871 on my old desktop with Windows XP no problems. Today I'm trying to get my MH-871 to work on my laptop Windows 10 (64 bit) I plugged the cutter into my USB and installed the Driver as instructed on this site, Cutter shows up under Ports Com 5, I didn't get the error about the driver signature so I didn't do the restart troubleshoot steps to disable the signature of the driver, it show the drivers installed and working properly but I cannot get it to come up as a printer, it keeps showing up under other devices Can someone help ?
-
MH 871 Windows 10 help
Bunky67 replied to Bunky67's topic in USCutter Refine Cutting Plotter Discussion
Yes I print from Coreldraw with this cutter on my XP machine all the time. but the Cutter shows up under my Printers as US Cutter, This one Does not it keeps showing up under other devices as FT232 USB UART. there seems to be an issue with my laptop and the drivers and the port or something -
MH 871 Windows 10 help
Bunky67 replied to Bunky67's topic in USCutter Refine Cutting Plotter Discussion
Ok so I went and did some checking under printers and devices it shows under other devices FT232R USB UART says my driver is up to date but no luck getting the plotter to come up. -
MH 871 Windows 10 help
Bunky67 replied to Bunky67's topic in USCutter Refine Cutting Plotter Discussion
I’m using Corel draw 2017. In driver instructions on this site it says that after downloading the drivers it should move from other devices into the Printers section of the device manager -
Ok thanks I got it figured out.
- 2 replies
-
- mh-871 refine
- driver
-
(and 1 more)
Tagged with:
-
I have a MH871 Refine MK1 and I’m looking for a driver so I can set it up as a printer via USB and cut through CorelDraw X5. Using XP will the MK2 driver work on the MK1?
- 2 replies
-
- mh-871 refine
- driver
-
(and 1 more)
Tagged with:
-
Can you use this set up on the standard MH 871 as well ?
-
I picked up a MH871 and I want to hook it up to my Dell which I already have a roland plotter connected to via Serial Port, Now I would like to hook up my MH871 to this same computer, I was thinking of running the MH871 via USB but have read of issues of the USB not being reliable. So my question is do I try the USB or can I buy a Switch box to switch between the two plotters via Serial cable?
-
MH871 USB or Serial ?
Bunky67 replied to Bunky67's topic in USCutter Refine Cutting Plotter Discussion
OK so do I which would be best, a 9 pin serial or 25 pin Parallel? -
MH871 USB or Serial ?
Bunky67 replied to Bunky67's topic in USCutter Refine Cutting Plotter Discussion
Well I will try the USB first then and if all else fails go to Serial for backup if necessary -
The mh871 I picked up the front measuring scale is in rough condition uscutter doesn't seem to offer a replacement. I have read where others have moved there scales to prevent the vinyl from catching. Has anyone found a replacement source? Or have any ideas
-
The mh871 I picked up the front measuring scale is in rough condition uscutter doesn't seem to offer a replacement. I have read where others have moved there scales to prevent the vinyl from catching. Has anyone found a replacement source? Or have any ideas
-
The mh871 I picked up the front measuring scale is in rough condition uscutter doesn't seem to offer a replacement. I have read where others have moved there scales to prevent the vinyl from catching. Has anyone found a replacement source? Or have any ideas
-
Picked up a used MH871
Bunky67 replied to Bunky67's topic in USCutter Refine Cutting Plotter Discussion
Yes I only paid $40 so I will be good if only the motherboard is bad Can someone tell me what is used for screws to hold the control panel to the top of the plotter? The screws in mine are gone Thanks -
I picked up a MH871 Cutter today, and I coudn't see it power up, So I got it home and powered it up and the Fan runs, the control panel screen lights but no words, and the 3 led's are lit, and none of the functions on the control board work, Where do I start to troubleshoot this? also does this take a special blade holder or is there aftermarket ones available ? Also how do you tell if the cutter is MKI or MKII ?