dugzphoto
Members-
Content Count
19 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Everything posted by dugzphoto
-
Thanks but it wont work for me. I need one already saved as WPC file. I can not convert
-
I am in need of a WPC file of an IMCA MODIFIED Does not have to be exact as attachment, but similar I am using BASIC 2009, and am unable to Vecotorize easily
-
Looking for a GOOD Jack Skellington for a black vinyl decal Would like something other then just head, maybe with body or bow tie
-
T H A N K S That is perfect and thanks for the convert too TALENTED daughter
-
The thing you need to be careful of, when tinting headlights and such. The headlight is plastic and it does expand and contract under heat and cold. Some of the headlight films are 30mil thick, and this will prevent the contraction and expansion; in-which will eventually spiderweb crack the lens
-
I appreciate it, but I can't open it
-
Ripping Vinyl
dugzphoto replied to dugzphoto's topic in Creation PCUT Cutting Plotter Support Requests
Mine does not have the pin on top, but I have read it. Thanks for your help -
OK So I am new to this used Cutter/Plotter. I finally got the blade to start in right position, but now it rips the paper. I have the pressure at 74, speed at 20 and using 2mil vinyl. The blade is barely sticking out. Is the blade dull or to much pressure?
-
Ripping Vinyl
dugzphoto replied to dugzphoto's topic in Creation PCUT Cutting Plotter Support Requests
I have come to the conclusion that the blade is dead. If I take it off and try and cut by hand, it is very difficult. The previous owner, had problems with it too. That is why they gave it to me Thanks for your help Have you asked the previous owner if he had this problem?? I am not familiar with the Pcut but if it has a removeable blade hoder like my Graphtec, take it out and try cutting some vinyl by hand with it (just use a scrap taped to your weeding table ) ..If you cannot get it to cut by hand at the proper depth something is wrong with the blade or blade holder.. gotta have a sharp blade, no gunk gumming it up, blade has to rotate easily..(Watch out a good blade is SHARP !!).. If you can make decent cuts thru just the vinyl and not cutting the backing paper, install the blade holder and play around with your pressure settings...Good luck! -
Ripping Vinyl
dugzphoto replied to dugzphoto's topic in Creation PCUT Cutting Plotter Support Requests
Your 2cents Not Needed -
Ripping Vinyl
dugzphoto replied to dugzphoto's topic in Creation PCUT Cutting Plotter Support Requests
Thank You -
anyone using WinPCSIGN Letter 11.0E
dugzphoto posted a topic in Creation PCUT Cutting Plotter Support Requests
Anyone using this program? I need help with settings -
Ripping Vinyl
dugzphoto replied to dugzphoto's topic in Creation PCUT Cutting Plotter Support Requests
May I asked, why you responded then? -
Ripping Vinyl
dugzphoto replied to dugzphoto's topic in Creation PCUT Cutting Plotter Support Requests
anything else you want from me? -
Ripping Vinyl
dugzphoto replied to dugzphoto's topic in Creation PCUT Cutting Plotter Support Requests
what do you use? -
Ripping Vinyl
dugzphoto replied to dugzphoto's topic in Creation PCUT Cutting Plotter Support Requests
WINPCSIGN LETTER 11.0E -
Ripping Vinyl
dugzphoto replied to dugzphoto's topic in Creation PCUT Cutting Plotter Support Requests
Blade is set at that depth here are other setting Weed Value 0 Curve Resolution 5 Panel Overlap 0 Knife Offset 5 Start Point Orientation is checked Depth ZDown 0 Work Surface 0 Height Zup 0 ZStep 100 -
Ripping Vinyl
dugzphoto replied to dugzphoto's topic in Creation PCUT Cutting Plotter Support Requests
OK so I have been messing with pressure. 60 does not cut it 62 cuts thru all of it (vinyl and paper backing) What next? -
CREATION PCUT CNT630 Driving me NUTS
dugzphoto posted a topic in Creation PCUT Cutting Plotter Support Requests
OK, I was just given this Cutter/Plotter and I can not figure it out. > 1) If I use SIGNCUT PRODUCTIVITY PRO the head goes to the right and hits Kill button. I turn on, push the on-line button and the X and Y come up. I set the vinyl 1inch from the right side and cutter on the edge of vinyl, push center button, push on-line. Then when I go to cut image it goes to the right and hits Kill Button (15 times now) Image is only 5inch and vinyl is 24. Also, I can not change size of image. Is this just a cutter program and nothing else? 2) If I use WINPCSIGN Basic, I can not set to Plotter. I am on COM6, it only goes to COM4 3) If I use WINPCSIGN Pro, demo version, I can set the Plotter, but since I am on DEMO it will not cut project it only cuts out the words DEMO